Jump to content
SAU Community

Remote Filter...oil Change ?

RustyR32Gtst

By RustyR32Gtst,
in General Maintenance

 Share

Recommended Posts

GeeTR Grand Master

GeeTR

Posted
Posted (edited)

Cooler and lines can add 1L or more. Depends on the level of "draining" you do. Some people actually disconnect the lines low, to get more of the old stuff out.

do u fill the oil filter or put any oil on the filter when u put a new one on?
smear some oil on the rubber seal of the filter, then screw it on as tight as you can with your bare hands. if it leaks, tighten a bit more with an oil filter wrench ($10) but it shouldnt have to be very tight

I think Luke meant, do you pre-fill the filter with oil before fitting.

Two hands is too much. Some Loctite anti seize and a good one handed twist should do fine. If it leaks, somthing is wrong. Those wrenchs are considered to be used for removal, not tightening. Snapping the filter thread isnt fun or cheap; iv never had one leak.

I had a GReddy oil relocator fitted to my car last week and with all the extra crap in the gtr we couldnt find anywhere neat to mount it on the strut tower like most people do, we ended up fitted it below the engine right next to the sump drain bolt with a little custom bracket.

I'm glad it ended up this way because their would be nothing worse than having a relocator fitted only to have oil piss all over the place because it is mounted upside down, that kinda defeats the whole purpose of it, if I wanted to make a mess I would have just left it where it is.

The anti drain back valve in most filters stops the mess, but a rag wrapped around the filter <-> boss works well.

Hope that filter doesn't taken a knock from a driveway / ripple strip

thats a good idea benm seen once in a mag, as i do reckn there a bit of an eye sore in the engine bay

I reckon they look shit hot, due to how much easier they allow a change on a GTR ;)

Edited by GeeTR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...