Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

im lead to beleive tenagah sell it..

Unit 4 / 12 Buckingham Drive, Wangara, Western Australia, 6065

Telephone: (08) 9408 0600

Mobile: 0433 213 106

Fax: (08) 9408 0533

Email: [email protected]

Steve,

I'd say go and get a total tune geared for the toluene, and consistantly run the same mixture if thats the case. If you have an ecu with provision for two maps then it's much easier I guess. Otherwise if it's a PFC then go into the Settings and tune using the adjustment so the entire map for ingnition and then fuel. It's less accurate but easy to remember and change on the fly afterwards.

The best thing to do is to pre-mix the toluene in a larger sealed container (fuel can) with fuel before adding it to the tank. Investing in a good system to pump it into the tank is a good idea as well as the funnels tend to be messy.

Edited by rev210

Josh, the rule of thumb that I use is 5% for every 1 RON, so 96 ron to 98 would be 10% - this is slightly overestimating, but would see you right AFAIK

Keefy, Tolulene is a aromatic hydrocarbon. It has several uses, including a cleaning solvent, paint stripper, making explosives and fuel additive to raise its resistance to knock.

It is, afaik, used by some fuel manufacturers for exactly that purpose, and it works quite well. I beleive F1 used to use high percentages of tolulene in their cars many years back.

I have found its a handy additive if you intend giving your car an unusually hard thrash, or even driving in the country where there is no 98 ron available (long interstate trips) just to keep knock under control. If you retune your car (as Rev210 suggests) you will get even better results as you can increase timing - because of the greater resistance to knock.

It will be very handy should I run out of 98 ron due to these bloody bp shenanigans :(

Never heard of that one. Octane boosters will often contain tolulene to boost the octane. Remember and octane booster will raise the octane by 4 points, which would take 96 ron to 96.4 ron - doesnt really help if you are chasing 98 ron.

Tolulene is added to petrol by the manufacturers to boost its octane rating (resistance to knock) - it will clean your fuel system, but it wont foul it. I have never had a problem, most I have used is 4L with round 30L in the tank - so approx 13%.

Rev210, how much have you used before?

Octane boosters usually double up injector cleaners, for the better ones. Maybe if u buy the cheap ass ones it will for all u know, but if u were to buy the better ones, it's good.

AFAIK, there are different specifications for octane boosters.

http://www.nitrous.com.au/products.html << this is one such example, which i've heard from workshops is effective. But to what extent, i don't really know. Anyone know if it works?

I've used this stuff for years.

Toluene is not used in modern off the shelf octane boosters and is used far less these days in basic fuels. There is a push to reduce the aromatic content of fuels such that BP98 doesn't contain very much by way of it at all, pick up a brouchure and it says the % from memory only about 7%?. Why you ask? because it's pollution and bad smell all the way ;) oh and catylitic converters don't like it.

up to 35-40% aromatic content in your fuel is fine if you tune for it.

the F1 turbo cars ran 79psi of boost and made 1,000hp and the base fuel was pure toluene with n-heptane thrown in to actually reduce the octane number to comply with regs, developed for the Honda turbo's at the time (alan prosts favorite from memory) the term 'rocket fuel' was coined at this time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...