Jump to content
SAU Community

Modificaton Order

PhilGTR

By PhilGTR,
in Engines & Forced Induction

 Share

Recommended Posts

PhilGTR Rising Star

PhilGTR

Posted
Posted

Hey guys,

Just looking for some advice on what to start with for modifications. I have a stock r32 GTR and i am looking to purchase apexi airfilters, trust intercooler, full exhaust system and BOV's. Would these mods be a good start? Any opinions appreciated! Thanks

Link to comment
https://www.sau.com.au/forums/topic/94730-modificaton-order/
Share on other sites
Beer Baron Grand Master

Beer Baron

Posted
Posted

firstly,

cat back exhaust (or if you have the dough go for dumps, fronts, cat and the rest)

either a K+N in the stock air box, or the apexi pods if you must

then you'll want a boost controller of some kind

Power FC is next and couple that with a set of cam gears

forget the trust FMIC on an otherwise stock GTR it's a waste of time and money. there is nothing wrong with the stock GTR cooler under 300rwkw. no real need for the bovs either as the GTR alread has nice twin bovs from the factory but if you are keen just make sure you get a GTR specific kit. I quite like the trust type R kit, or the blitz super sequential is nice too. i can't stand the HKS ones though.

PhilGTR Rising Star

PhilGTR

Posted
  • Author
Posted
firstly,

cat back exhaust (or if you have the dough go for dumps, fronts, cat and the rest)

either a K+N in the stock air box, or the apexi pods if you must

then you'll want a boost controller of some kind

Power FC is next and couple that with a set of cam gears

forget the trust FMIC on an otherwise stock GTR it's a waste of time and money. there is nothing wrong with the stock GTR cooler under 300rwkw. no real need for the bovs either as the GTR alread has nice twin bovs from the factory but if you are keen just make sure you get a GTR specific kit. I quite like the trust type R kit, or the blitz super sequential is nice too. i can't stand the HKS ones though.

Yeah i was thinking of getting the trust Type R BOV's. Okay so i think i will get my Trust power extreme 2 cat back exhaust first with a high flow cat and a trust front pipe until i get paid <_< . My front mount seems a little dirty, im not sure if its still efficient.. how much does it cost to get it flushed and cleaned?

Jago Mentor

Jago

Posted
Posted

don't waste your money on aftermarket BOV's, your standard ones work a treat.

Pod filters, you don't have to, the mines car is still using the standard airbox with a panel filter upgrade. GT-R cooler is good for 300 odd kw, as mentioned above, the just jap race car still uses the stocker.

Go for an exhaust, aftermarket ECU, an EBC and some cam gears to start off with and then go from there. Next thing after that will probably be a fuel pump, clutch, maybe injectors, cams, more boost? upgraded turbos?

Anyone?

PhilGTR Rising Star

PhilGTR

Posted
  • Author
Posted
don't waste your money on aftermarket BOV's, your standard ones work a treat.

Pod filters, you don't have to, the mines car is still using the standard airbox with a panel filter upgrade. GT-R cooler is good for 300 odd kw, as mentioned above, the just jap race car still uses the stocker.

Go for an exhaust, aftermarket ECU, an EBC and some cam gears to start off with and then go from there. Next thing after that will probably be a fuel pump, clutch, maybe injectors, cams, more boost? upgraded turbos?

Anyone?

ok thanks for that! what sort of boost is it safe to run with the stock cooler? would something like a greddy emanage piggy back computer be good enough or should I go a full replacement computer? Im only looking to mildy mod my car. like 240kw or so?

paulr33 Grand Master

paulr33

Posted
Posted

the stock bnr32 intercooler should be for around 300rwkw

however the exhaust wheels on the 16 year old turbochargers wont be.

they will let go near 1.0 bar and then youll have to fork out for a new turbo (or a pair) and thats if it doesnt do any damage when it fails, which it has known to do on the rb26. more boost means more heat simple

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      First time we have seen lights 
    • Wazmond
      WGNC34 - floor mats

      By Wazmond · Posted

      I think Fitmit had some, have a look on there (theyre Australian as well)
    • soviet_merlin
      Howdy Y'all

      By soviet_merlin · Posted

      Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...