Jump to content
SAU Community

R33 Modification

R33A31

By R33A31,
in Engines & Forced Induction

 Share

Recommended Posts

paulr33 Grand Master

paulr33

Posted
Posted

injectors (stockers run out of capcity around 200-230rwkw, 550cc minimum)

airflow meter (stocker runs out of capacity around 220rwkw, z32 or q45 afm)

tyres (stock or crappy tyres will just result in lots of wheelspin)

suspension (standard suspenion will hamper your launch capabilities)

brakes (stock calipers should be ok, but you should look at some good rotors and / or braided brake lines and good pads)

ecu (stock ecu will be useless. go for aftermarket stand alone. recommend apexi powerfc)

fuel pump (stock pump will run out of capacity around 200rwkw)

intercooler (stock intercooler will run out of capacity around 180rwkw)

exhaust (stock exhaust will be useless, at least 3.5" dump pipe / front pipe and 3.5" exhaust with hiflow cat)

boost controller (good a good bleed valve or electronic controller)

pineapple kit (to prevent axle tramp)

standard plenum is fine (no need to change)

here's a base line list, you just need a suitable turbo.

hiflow of the standard unit should get you to 250rwkw easily without any extra lag. once you go past that stage you need to look at internals and consider how much money you really have and what your target is.

Link to comment
https://www.sau.com.au/forums/topic/95363-r33-modification/#findComment-1725956
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...