Jump to content
SAU Community

Recommended Posts

ok guys, while i'm doing my rb30 conversion i'm putting my new cooler on, firstly i just wanna know is this how it should be mounted? Secondly i want to keep the standard route for the cooler piping for the stealth look so the outlet on the drivers side needs the 180 degree pipe but i can't see where its going to go! the only place i can see to put it is under the cooler but won't it hang below my standard type m spec front bar, which i don't want? And lastly has anyone been able to keep/relocate they're spot lights on there 32 after putting a cooler on as i couldn't see how i could keep them.

pb2500012do.th.jpg pb2500029gu.th.jpg pb2500037rb.th.jpg pb2500046ax.th.jpg

cheers in advance!

Link to comment
https://www.sau.com.au/forums/topic/96216-r32-cooler-question/
Share on other sites

You saw my Stagea yesterday at the dynoshop - thats got a front mount with return feed to the standard holes in the 'airbox' side of the engine bay.

With the 'dohnut 180degree pipe' maybe install at an angle going under the engine as such, in lieu of straight down.

Im still able to use the spotlights, for photos see Stagea section "the intercooler thread".

Edited by bwilkeson

I was able to keep my fog lights when i installed the intercooler. I just modifed the brackets for the lights a little, ie cut off the bottom section and mounted the pipes hard up against the lights. There is a tiny bit of overhang, but its a standard bar. Dont know how your going to get the pipe running under it back to the stock pipe though, maybe offset the pipe so that it runs behind the intercooler and back to the origional pipe.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...