Jump to content
SAU Community

Recommended Posts

most of the time when i quick shift from 1st to 2nd gear i can feel the gears crunching together, but you dont hear much of a crunching.but if i gear down e.g- from 4th to 2nd it never crunches.

if im driving normally from 1st to 2nd it doesn't crunch at all.

recently did a gear box oil change using standard oil, and was doing it before oil change.

would it be my 2nd gear syncros.

i heard mayb using redline oil may help..

anyone got any suggestions....cheers

Link to comment
https://www.sau.com.au/forums/topic/96264-crunching/
Share on other sites

Hi mate...

I've got similar problems...

I've got an R33 RB25DEt and I love it.. My transmission is fine at slow changes and quick shifting but as soon as I get over about 120km/h... whenever I change gears... the teeth grind...

I've been told the syncros are half stuffed.. I don't really know much about transmissions so if anyone else can shed some light on the subject, that'd be great.. I could reccommend changing your oil as well... get some good oil this time..

Link to comment
https://www.sau.com.au/forums/topic/96264-crunching/#findComment-1745175
Share on other sites

Redline or use some slick50 treatment. Or Nulon. I think Slick is the best. Couldhelp reduce the problem. Since you have already replaced the oil I would buy a ttreatment of some sort...siphon out a little gearbox oil and add the treatment. Drive for 1000kms see if it gets better...If not - take out a little bit more and add another additive...

Not sure if it will be bad to mix but the box doesnt sound thmuch good anyway...

Redline is more just a decent gear oil - I think the traeatments have more of a chance of working.

Edited by benl1981
Link to comment
https://www.sau.com.au/forums/topic/96264-crunching/#findComment-1745471
Share on other sites

I just changed the oils in my r33 gtr to redline synthetics and the gearbox is alot smoother however I am now getting a clunking noise in reverse that is amplified by this oil. I have been told the noise is normal though but it is anoying.

Would recomend it though as it was stiff through the gears before and had a it of a whirring sound coming from the drivetrain that has significantly been reduced.

sb..

Link to comment
https://www.sau.com.au/forums/topic/96264-crunching/#findComment-1749978
Share on other sites

i changed my gear box oil to reline synthetic. so far ive driven 150 k's after changing the oil. changing into 2nd doesn't grind and crunch anymore, and the gear shifting has gone smoother. I did not adjust my slave cylinder as the mechanic said i only needed to adjust it if it was crunchin in every gear. So far so good.

Thanks for the help!

Link to comment
https://www.sau.com.au/forums/topic/96264-crunching/#findComment-1753137
Share on other sites

I had synchro issues with 2nd & 4th gears..

Changed to Redline Lightweight Shockproof, synchro issues resolved.

I would rather try a $130 high grade oil first than get my box pulled down and the synchro's replaced.

Hmmm let me see which is it $130 or $1500 for parts and labour getting the box pulled apart..

Link to comment
https://www.sau.com.au/forums/topic/96264-crunching/#findComment-1756664
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...