Jump to content
SAU Community

Recommended Posts

just though i would let you guys know wot i got from the prince after the big dyno day..... it was 126kw at 152kph in 4 gear....

now wot cheap mods can i do to the rb20 to increase that figure that wont break the budget?

wot i have know is a rb20det, 450 x 300 76 front mount, pod filter with cia, standard turbs standard dump, retrofiited r 33 exhaust, custom 2.5 inch intercooler piping.....

any help, greatly appreciated

Pete

Edited by 66 skyline gt
Link to comment
https://www.sau.com.au/forums/topic/97107-the-big-dyno-day/
Share on other sites

Is it a late model RB20DET?

If it is.... Keep the stock rb20det turbo for response, dial in 1bar with an EBC or bodgy actuator mod (get it holding boost) then do the ecu. It should make around 170-175rwkw and pull hard from 3000-3500rpm to 7000rpm. ;)

In order of priority..

Dump Pipe, nice cust 3" exhaust with a straight through muffler, 1bar boost, ecu/safc or what ever.

What diff ratio are you running?

That thing would hammer. :P

Edited by Cubes
Link to comment
https://www.sau.com.au/forums/topic/97107-the-big-dyno-day/#findComment-1762757
Share on other sites

na, have a 450 x 300 x 76 ic behind the grill stashed away with 2.5 inch custom ic piping.......

i heard ya should push much more than 12 thru the stock turbs of the ceramic wweel goes BANG!.....

Link to comment
https://www.sau.com.au/forums/topic/97107-the-big-dyno-day/#findComment-1763574
Share on other sites

On the rb25det yes.. If you push more than 12-13psi they tend to let go.

The ceramic turbo's on the rb20det you are able to run around 14psi or so.

I ran 1bar for ~3years and 100,000km's until I dropped the rb30det in that due to the rb25 head flowing so much better required 9psi on the same stock turbo to make ~10rwkw more power.

It also has a lot to do with driving conditions as what kills the ceramic turbo's isn't boost its EGT's. High EGT's due to poor tuning, detonation OR track work kills ceramic turbo's in a flash.

Using a ceramic turbo for track use I would be nervous to push more than stock boost through it, simply due to the heat, even then ppls have had turbo's let go at the track on stock boost.

Roy (Troy) in his R32 pushed 1bar or 14psi I don't remember through his and attended multiple track days without a failure so at the end of the day when it comes to track use its luck of the draw.

Push 14psi through it, providing afr's and ignition are good with no detonation it will be perfectly fine. :P

I have a spare RB20DET turbo laying around here should you prove me wrong. :D

The RB25 exhaust.. I think they are 2.5"? If so replace the muffler with a straight through. That will bring power up.

Edited by Cubes
Link to comment
https://www.sau.com.au/forums/topic/97107-the-big-dyno-day/#findComment-1763732
Share on other sites

  • 3 weeks later...

hey pete. its Darren here im friends with mark n mel.. i have met you a couple of times a while back.. i have a brand new stainless dump sitting here next to me that i dont need if ya interested.. $150 and I reckon i even have the gaskets etc..

Link to comment
https://www.sau.com.au/forums/topic/97107-the-big-dyno-day/#findComment-1824088
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...