Jump to content
SAU Community

Recommended Posts

hey guys i went down to see my car about 4 or so days ago and saw my car now they were moving the car in and out fo the factory each morining and night and so more as well, now i notice the air flow meter was not hooked up or there and the hose from the top cooler pipe to the waste gate was not there either, now i went down today and they siad it run out of fuel on idle and so they filled it up and now it runs crap and just stall and willnot cleanly rev like you hold it at 2500 or 3000 and it not like what is used to be and i have some noise in the area or my cams and timing case which i never had whole thing just sounds really bad ,now first the car shoulnt run whith out the af meter and no hose on the wastegate i could only imagine, now i spoke to my mechaninc and told him he siad could be a dead meter or fowed plug(s) or vacume leak , now it has a new hks cooler kit, so i am wondering has some one drivin my car and Ducked it

no for people who dont know i crashed my car and i stuffed my fmic and guard etc and some side panels 1/4 etc not pretty. now could a hard impact stuff af meter cause it did hit there and break a mount on my airbox, and bent cooler pipes and put holes in it .now is was dirty and dust grassy crap in my engine bay after accient from shrubs etc so could this have gotten sucked up and done bad stuff, the car was drivin about 5 or so ks to a friend place ,so could that have done something to anything.

any advice would be great just trying to figure out if the panel shop has stuffed my car

Link to comment
https://www.sau.com.au/forums/topic/97972-r33-s2-running-very-crap/
Share on other sites

Are the intercooler pipes connected? Will not idle properly if they're not.

Is the AFM connected? Couldnt' work it out from your post. If its not, it won't idle/run properly.

I'd say in any case your plugs have been fouled.

dude, if you've had a bad front end smash do you really think its going to run ok?

Get the chassis fixed, then take it to a mechanicfor diagnosis. If you're claiming insurance, then this should be covered.

By the sounds of it, there are air leaks everywhere, afm isn't even plugged in, and all of your pipes are bent.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...