Jump to content
SAU Community

Recommended Posts

Hi guy's,

99gtt and others, if someone is in Sydney and can come in to see us with thier 4 door, we can see what changes we need to make and we can make up the 4 door kit.

FLIP, the front bar by itself is $440, as is the rear and skirts are $300 for the pair by themselves.

xr8eater, We will be looking at a R32.4 and R33.4 conversions next year. Once we have the normal wide body guards available for each model, then we can modify them for the conversions.

choyda, No he put the canards on himself.

Jeff.

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1801734
Share on other sites

xr8eater, will do.

E-Lu-Shun, I will send you a PM.

R34, We haven't got any kit for them as yet. You must have one of the very few in the country at the moment. I have heard they will be released here new next year I believe, although they are apparently the shitty FWD and 4WD versions. We will be working on a Z33 kit sometime next year and we could probably adapt a kit for the V35 from there.

Jeff.

Any kits coming for V35?

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1803509
Share on other sites

R34, We haven't got any kit for them as yet. You must have one of the very few in the country at the moment. I have heard they will be released here new next year I believe, although they are apparently the shitty FWD and 4WD versions. We will be working on a Z33 kit sometime next year and we could probably adapt a kit for the V35 from there.

Jeff.

OK thanks please keep me posted.

Yes my car arrived yesterday from Qld.

Don't think V35's come as FWD...maybe you are thinking Maxima?

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1809779
Share on other sites

Unfortunatley by the sounds of things they will be coming out in a FWD format in Aus :P:D , or at least that is the word from my mate at Nissan.

Pretty crap hey.

Jeff.

OK thanks please keep me posted.

Yes my car arrived yesterday from Qld.

Don't think V35's come as FWD...maybe you are thinking Maxima?

Link to comment
https://www.sau.com.au/forums/topic/98299--/#findComment-1809806
Share on other sites



  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...