Jump to content
SAU Community

Recommended Posts

I don't believe they will destroy the coil packs, but if you have standard coils irridium plugs will make them work harder. For the best performance with these plugs you probably need a set of split-fire coils and have your plugs gapped correctly. i.e. high boost smaller gap around 0.8 to 0.9mm. Standard boost then the 1.1 gap will work ok.

I changed to NGK irridiums about 4 months ago and had nothing but trouble, misfiring, hesitation in the mid rev range. The smaller gap solved the misfiring but the car just never reved the way it used to. This is because my standard coil packs couldn't handle the irridium plugs.

I recently changed my irridiums to NGK copper ®, gapped them at 0.9mm and the car runs like a dream. They will only last about 20-30k depending on how you drive, but for $20.00 for a set of 6 who's complaining.

If you feel that you need the better plug, best to stick with NGK platium. The only problem is they come pre-gapped so you need to order them with your preferred gap.

Paul.

umm, okay. So, should I be overly concerned about this? Does damage usually occur within weeks, or do I have a few months?

Its not really damage that occurs, it's just that they don't work as well. Especially if the coil packs are getting older this doesn't help. Eventually of course a coil pack will die. If you stick with irridums then use splitfire coils, around $800.00.

Paul.

in a good way thats good to know..when I bought my skyline almost 3 months ago, my mate made me buy the iridium plugs. Spend a fortune, then figured it was too much hassle to change them, on account of the ornament and piping covering up the plugs and coils..so they've just been sitting there in my garage for the last 3 months...

Hey can someone please explain why you guys are making the spark smaller??? I dont understand, really it doesnt make sence, well not for me anyway.

I thought the bigger the spark the better the bang?

also matty_tonkin Super cheap sell them, $20 for a set of 6

Edited by 7yphon

The deal with closing the gap is that with running higher boost the forced air can blow the spark out.

Which causes the car to go and sound like a heap of crap when it hits full boost.

I bought Iridium 0.8's for my car when it came over because even though running factory boost levels it wouldn't handle it when it hit around 5000rpm.

And plugs that were in it were Iridium 1.1's

but ive heard that compared to japan our premium fuel quality would be there everyday cheap stuff.

Thats what i know anyway, hope it helps. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...