Jump to content
SAU Community

Recommended Posts

Anyone know the best way to fix a few rattles in the R33

When I hav ethe stereo off I can hear a noise around the console and another near the air vent on the drivers side - the one above and on the dash - to the right. If I put pressure on that one the noise from there stops. It doesn't appear to be loose though.

Just wondering if anybody had embarked on a de-rattle program for their car. Its th only thing tha makes it feel old - as the performance and comfort is pretty good.

CHEERS

Edited by benl1981
Link to comment
https://www.sau.com.au/forums/topic/98996-fixing-interior-rattles-anyone/
Share on other sites

Check that all the proper screws are where they should be. Failing that, take off the offending item, and put a thin strip of rubber (self-adhesive) along the inside of it, then screw back in.

Just make sure the rubber is thin enough that it seals the gap that is vibrating, but not too thick that it seperates the two peices of plastic noticeably.

The rattle from the air vent area is actually the air vent. I have it too in my R33 (from the driver side vent and sometimes from the middle too as well). The little A/C vents that you can change the angle of are guided by a small, loosely held plastic bar at the back of the vent "box" which moves the angled 'slats'. I think to stop the rattle, it could mess up the vent working properly. But you could try. Alternatively, just block up the A/C vent and not hear anything at all from all the sweat clogging up ur ears :D

All car's make road noise. Even Ferraris, Lambos and BMW's the same age as our cars (and some younger!) will rattle. Obviously some can be fixed/dampened (ripped my old Civic apart trying), but some can't be found because they are caused by interaction between the trim and the chassis or whatever and you won't see the cause when u open her up cos u can't reproduce the sound. Many a time I had my bro monkeying around in the Civic pinpointing noises while I drove over a bumpy stretch of road ;) And often to no avail.

BTW, Honda's are the WORST for rattles. Go ride in a 10 year old honda then get back in ur R33 and u'll stop complaining :D

lol... it usually gets noisy because someone has pulled it apart to fit a stereo, fix a wire, fix the A/C blower, etc... Then there's the stiffened suspension, doesn't help.

Most cars that i've been in that are totally stock are dead quiet apart from whatever is in the glovebox moving around.

If you can pop the vent out, you should be able to reattach the brace along the back of the sliding adjuster. Put some clear bike grease along where the slider runs. It's sticky to the point that it won't allow the plastic to touch and rattle, but will make the vents glide better than standard.

Randy - I just popped the top vent that doesn't have any mechanism on it (near derivers side door in dash and put some double sided tape around.

It's a bugger cause I just had all the vents out for when I did the stereo - could have lubed them then...oh well.

ben.. you're looking at the fixed vent(s) that cycle air through the cabin regardless of the A/C settings.. I was talking about the 4-direction adjustable A/C vents on the front face of the dash. There is the box that holds the vent. Then there is a bunch of "fins". And holding those fins is (I think it's just one) a piece with the little handle u push/pull which connects to a bar holding the rear of all the fins. It's THAT part rattling against the fins. Greasing/whatever will probably work as mentioned before. Just checking you were looking at the right part(s). Sucks to be annoyed by the little things, eh :rofl:

benl1981 is the noise you're talking about the one that sounds like something's bashing from side-to-side inside the central vents? I get the same problem, not very often, but it seems to go away with a small hit to the top of the vents or by turning the climate control off, and then back on again. So I'm not so sure its an adjuster... it's more like something's flapping around inside. I haven't had a chance to pull anything apart, but I'm thinking the actual vent connections themselves might be the answer (the tubing).

Sorry, speculations are all I have at the moment :starwars:

Stiffer suspension ALWAYS causes rattles.

My then 3yr old VS V8 Commodore was perfectly silent, dropped it with a Whiteline kit and within 6 months it was starting to rattle around the dash and door trim.

My little R32 is now 13-14yrs old, still the stock sloppy jaloppy suspension and ZERO rattles. :P

Yeah I'd have to agree. When I first bought my 33 it was quiet as, but now after driving around on bumpy roads, it's starting to get a few rattles here and there.

I guess sometimes these things are just inevitable.

Stiffer suspension ALWAYS causes rattles.

My then 3yr old VS V8 Commodore was perfectly silent, dropped it with a Whiteline kit and within 6 months it was starting to rattle around the dash and door trim.

My little R32 is now 13-14yrs old, still the stock sloppy jaloppy suspension and ZERO rattles. :huh:

I too have a rattle around that area, one weekend i took the fascia and dash all the way out. Checked the parts i had pulled out, no loose bits, stuck my hand into every nook and cranny under the dashboard, again no loose bits.

So went for a drive with all the stuff out. The rattle was still there but sounded more like metal on metal, stuck my head outside the window while drivin and it sounded like it was comin from under the hood, checked under there but no loose bits either. Pulled the grill off (where the water runs down into off the windscreen) no loose wiper motors or bars or anythin).

So im guessing its inside the car, right up under the dash, something banging on the chassis for it to be audible outside the car.

Im positive thats where the noise is, but cant get to it with taking the whole dashboard off, which is a big project. So if anyone has any ideas what it could be lemme know before i got writing off my car

cheers :-)

I havent found my issue yet..but theres been a few good ideas here.

One noise I did have Wez was a piece of rubber that is under the bonnet to sort of seal and stop water from windscreen going further into engine bay. Runs across near the shock towers. This goes a bit hard and squeeks a bit as it rubs on the bonnet. Put some tape around there or something to stop it rubbing on the bonnet. That stopped one of my noises but then you find another!!

Doesnt realy sound mechanical though.

Edited by benl1981

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...