Jump to content
SAU Community

Doing My Homework

LTHLRB

By LTHLRB,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

LTHLRB Grand Master

LTHLRB

Posted
  • Author
Posted (edited)

ah right right, do gtr injectors fit in the std rb25 fuel setup and would i need an ecu if i upgrade them? i know that with the rb30's its u haveto change the ecu if u have the injectors. But im not too sure on the rb25 ecu.

Edited by LTHLRB
Jetdat Veteran

Jetdat

Posted
Posted
According to HPI stock r33 injectors are only 370cc/min and as such run out of flow at around 200rwkw.

really???

i have about 200rwkw with standard injectors and the are nowhere near their max duty cycle...

i think they are only at around 70%...i thought 250rwkw was achievable with standard injectors??

also dont believe everything you read in magazines, rather talk to people with experience...

boj01 Experienced

boj01

Posted
Posted
aren't SR20 injectors side feed as well?

Yes, SR20 injectors are also side feed. You will need to buy larger Sard/Nismo/Bosch/Denso injectors if you want an upgrade as there is really no standard injectors that are an easy side feed upgrade.

cogs Experienced

cogs

Posted
Posted

I thought I read S15 injectors (side-feed) were a straight fit on R33 GTST? They aren't 550cc but they are higher than r33 std 370cc, maybe 470?

Also GTI-R SR20 injectors are top-feed and some side-feed SR20 injectors are only 370cc so same as R33, so if you go sr20 make sure you get the right ones.

LTHLRB Grand Master

LTHLRB

Posted
  • Author
Posted (edited)
Well how much power are you chasing?

If Jetdat is right then you can get 250rwkw with std injectors.

The most i can get in standard from, standard being ecu, bottem end, cams. Maybe around 200 - 250 rwkw. Ultimately in the long run around 300 350 rwkw using a 35/40 and maybe rb30 bottem end rebuilt with steel rods and forged pistons and a good set of cams.

Edited by LTHLRB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So been ocd with timing mark but checked from few angle and seems both cam are on and crank is matching as well to the slot on sump and crank pully   i noticed crankshaft cover has been robbed as per attached pic. Any ideas why? Could my balancer or harmonic be on its way out? should I replace the cover? https://ibb.co/ZR1JFYRR
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • sunsetR33
      braided lines for the turbos

      By sunsetR33 · Posted

      Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 1: I did some work on the car already before finalizing this post and my "issues" list. I dropped the Tomei exhaust in favor of the HKS Hi Power Silent. Sounds nice and I can actually hear myself think now. Also gives me a realistic chance to legally drive without silencer inserts. A bit of cheating was necessary to still be able to mount the Top Secret style diffuser. Some malusage of washers and a bit of "convincing" toward the brackets and exhaust hanger seemed to do the trick. The shaky steering wheel has been resolved as various suspension components were worn, like sway bar bushings and link bars. Most notably the two steering tie rod ends. Had some trouble finding bushings because my sway bars are not OEM thickness, 23.x up front and 27 rear. But non adjustable, so no aftermarket I suppose. Maybe they are nismo units? Turbo oil drain hoses were definitely still the originals and are new now. Wasn't the cause of the turbo oil leak sadly. Currently removing the rear turbo because of it, I suspect the braided oil feed line is the culprit. This issue needs to be dealt with so I can work towards actually getting the turbo setup legal and inspected. Two new issues to add to the list as well. Rear Main seal is probably leaking. Time will show how bad it is, I don't really want to drop the gearbox right now just for the stupid seal. Could fix a few other things in one go once I do that. Front right driveshaft grease is going past the cv boot, so at some point I'll fix that too.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Ok so no 4cyl clutch... Yeah it is a factory manual. So if iam correct i need clutch and flywheel too? I can use something that suits something like R32 GTST?   EDIT: https://www.ebay.com/itm/224291042776 Is this ok?   EDIT2: i maybe forget to mention this(dk how important it is) but the trans will be behind RB25DET NEO(iam doing swap) It will be there for a little while. Iam planing to do bigbox or BMW tranny..
×
×
  • Create New...