Jump to content
SAU Community

Recommended Posts

This mite be a stupid question but as far as i know the V8 supercars use a spark plug near the end of their exhausts to create the fire you see out the back...i think this is there so it creates some sort of back pressure or something like that...

i guess wat i'm asking is if we were to place a spark plug near the end of our exhausts wouldn't that cause a pull of air through the turbo on gear changes keeping it spinning.

i'm not looking to do this for the rice factor just interested if it would work and how i wud go about doing it.

also would there be a way to turn it on and off.

thanks for any feedback...also be nice with replys i'm learning still.

cheers, Mark

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/
Share on other sites

you can use aftermarket 3rd party tools to help assist with turbo lag and "spooling up" if this is what you are referring to? I suggest you do a search on anti-lag. the idea is to retard the timing and dump fuel on gearchange to keep the exhaust housing spinning and so when you come back on throttle the turbo is still spinning at a higher speed that it would have been when you back off throttle the normal method. the result well in theory is not as much lag as the turbine is still running at a high speed, enough to bring the compressor back into its efficiency zone quickly

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1817534
Share on other sites

Back pressure is not something you want in a turbo setup. That will increase lag, not decrease it.

So, logically speaking, if the V8 Supercars were igniting fuel in the exhausts to generate back pressure...it would be counter productive on a turbocharged car. It wouldn't "pull air" through the exhaust - it would just block it.

Of course, as people have said above its not the case. You can blow flames just as easily in your car by pulling out your cat and running non-baffled mufflers. Just rev the car hard and pop off the gas.

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1818662
Share on other sites

A fair few pro off-street race cars will run anti-lag. Most involve dumping excess fuel on throttle-off (normally by running it rich and taking timing out), and will either use a spark plug in the turbo's exhaust housing or rely on the hot turbine itself to ignite the fuel.

Normally they'll use an aftermarket ECU, so you can program and choose what conditions you want the anti-lag to kick in.

Aside from being very street illegal, you have to be a pro racer to run such a setup since your turbocharger then becomes a consumable. There's few faster ways of f**king your turbo's wheel than causing explosions on them.

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1818665
Share on other sites

like i said it was just someone telling me they had been wondering about it who maybe doesn't know much at all. ohwell was worth asking...i didn't think it sounded right hence the "be nice with ur replies" part

Link to comment
https://www.sau.com.au/forums/topic/99774-faster-spool-up/#findComment-1818870
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...