Jump to content
SAU Community

Hks Hi-power Exhaust

BLKSKY
 Share

Recommended Posts

BLKSKY Enthusiast

BLKSKY

Posted
Posted (edited)

Item: HKS Silent Hi-Power Full Stainless Steel Exhaust for R33

Location: Melb

Item Condition: Immaculate

Reason for Selling: Changing to a different exhaust

Price and Payment Conditions: $700 + Freight

Would prefer pickup.

This is 3" at the cat and goes up to 3.5"-4" towards the rear of the system. It is full stainless steel all the way. This ehaust gave me 170rwkw with just 10psi and apexi pod. It has the most orsome snarl when on boost.

Because this is full stainless id hate to think how much they would be new. As can be seen from the photos it is very clean with absolutely no dints or scratches.

Will also suit show car or extreme power chaser.

contact me on 0417 280 308 or [email protected]

Cheers

Gene

post-16215-1135752454.jpgpost-16215-1135754676.jpgpost-16215-1135754747.jpg

post-16215-1135754809.jpgpost-16215-1135754854.jpgpost-16215-1135754890.jpg

Edited by BLKSKY
Link to comment
https://www.sau.com.au/forums/topic/99905-hks-hi-power-exhaust/
Share on other sites
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      No engine fan = quieter getrag ???

      By Butters · Posted

      Saw this video today from Adam LZ.    Long story short is he is claiming that the load from the engine fan once the fan clutch heats up(engaged) is increasing the getrag rattle(at idle) when you don't have a dual mass flywheel.  Before I go buying an electric fan setup .... Anyone heard of this ?    I must admit when my car is cold the getrag is pretty quiet and I do notice the rattle after it is all warmed up. I've always assumed this is due to the gearbox oil temp and tolerances of metal.       
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
×
×
  • Create New...