Jump to content
SAU Community

Recommended Posts

i know today is extremely hot (42-43 degrees)

but i think my car has a problem

normal driving, the car goes up to around 110 degrees (quite quickly) on the r34 temp gauge (dunno how accurate it is but it has never went past 90 before)

there is VERY hot air blowing out under the car and towards the front of the driver side bumper

air coming out the exhaust is hotter than usual and seems to burn

also, my air-cond does not work and only blows out hot/warm air

any suggestions?

Link to comment
https://www.sau.com.au/forums/topic/100273-heating-problems-help/
Share on other sites

Coolant should start boiling at around 120degree's providing the system is holding pressure (no leaks) and the correct coolant mix/ratio has been used. Its the oil temp at these coolant temps that is the worry. :S

Check the fan's viscous clutch.

Chances are its stuffed. :P

If its not check the thermostat then radiator.

Providing your running decent coolant with the correct mix it shouldn't boil until around 120degree's. Its the high oil temp that follows the high coolant temp that is the worry.

A couple ways you can test the fan.

When stone cold... star the car.. you should hear the fan roar for 15seconds or so. If it doesn't then its stuffed. :(

Once warm... Pop the bonnet then turn the car off while you watch the fan spin.. As the motor stops the fan should follow, it should not continue spinning freely. If it does then its stuffed. :(

I have noticed with mine it appears the car disengages the a/c once engine temps get too high. Unsure if its just a coincidence or if its really the case. Mine appears to do this when I've had cooling issues in the past.

Mine often hits 90degree's with the a/c on in traffic on a hot day.

The genuine thermostates make the car run a little warmer.

Aftermarket items (from supercrap and the like) open earlier and wider causing the car to no longer reach operating temp within 2km's and also it never really hits the 'correct' operating temp, being ~82-85degree's.

85degree's is apparently the optimal temp for fuel economy.

I'm in the process of dropping a nice 14" thermo fan in front of the A/C condensor to replace the std 12". Should help on those hot days sitting in a traffic jam as the stock fan draws stuff all air at 800rpm. :blink:

The proflow thermo's from Ebay are cheap and work well. Flow more than the davis.

On these hot days I've also noticed the pwr steer gets a little heavy and fluid appears to blow out the top of the reservoir a little, looks like a slight seep around the edge of the cap. The answer is to fit a power steering cooler. easy done many aus cars have them for this reason.

Head to the local track and you will find the pwr steer fluid appears to boil over, some I know of have placed a sock over it to prevent too much fluid going everywhere.

Edited by Cubes

thanks cubes

will test out the cold start and warm test tomorrow (neighbours may not appreciate me turning the car on right now lol)

i noticed today that there seemed to be ALOT more air blowing from under the car..

also tried spinning the fan when the car was off and the fan moved from one blade to another with the flick of a finger, is this the normal distance?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...