Jump to content
SAU Community

Recommended Posts

I want to put a turbo kit on my R32 GTR and i want a response car. so if any one can steer me in the right direction that would be great. my r32 is basicly stock has a exhaust. so any other parts that might help me with making a response car please tell

Link to comment
https://www.sau.com.au/forums/topic/100875-gtr-turbo-kit-help/
Share on other sites

how responsive are they. what is the rpms a soon as full boost comes on?

http://www.skylinesaustralia.com/forums/in...p?act=Search&f=

cheers.

Its all covered, depends on your engine spec.

Have a read of the threads.

Same thing for 2530's

GTR Garrett 350HP Upgrades

707160-5

pnblight uses them in WA and makes 500+rwhp with supporting mods

They bolt up to all the standard oil and water lines as well as dump pipes

several customers have pointed out, that they see a difference of 3-500rpm

Thanks

Tarek

RACESPEC

this is not the for sale section, traders can use thier own sections freely, not FI

cheers - R31Nismoid

I want to put a turbo kit on my R32 GTR and i want a response car. so if any one can steer me in the right direction that would be great. my r32 is basicly stock has a exhaust. so any other parts that might help me with making a response car please tell

the best two units are

Garret gt2560r 707160-5

Hks 2530

I personally not very interested in the gt-ss as you loss top end with no real gains in the bottom end over the 2530 or gt2560r (personal opinion )

both direct bolt on and both very similar, if i had to pick the differences the garret will spool a little earlier and make a little more hp at lower boost BUT the HKS is capable of high boost and comes in to it own in this area but these not a lot of motors that will run 1.5 bar plus which is where i believe the HKS start to over come the garrets

Racespec can supply the garret at a very good $$ much cheaper thean the hks unit new out of japan (comparing new with new)

I have run the garret turbos through all the stages of my build up from std with exhaust 12.08 1/4 miles (std air box ,injectors,afms, ecu ) to 529.4rwhp at 20 psi

pete

2530's mate...i made over 440AWKW on race fuel and over 400AWKW on pump gas also made 467RWKW on 103unleaded....runs 10.3's and goes like a rocket off the mark..1.4-1.5 60' times...i might have a set for sale if you are interested...pm me

Edited by DiRTgarage

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...