Jump to content
SAU Community

Manual Gearbox Issue

R32GTS4
 Share

Recommended Posts

R32GTS4 Apprentice

R32GTS4

Posted
Posted

G'Day all,

last night I jumped into my car and could not select reverse. :(

The car is a manual '89 R32 GTS-4 (turbo), with only 42k on the odometer. I've added 19k since I imported it March 2005.

There is no history to my knowledge of any gearbox issues until now. I still cannot select reverse, while all forward gears engage as per usual. Clutch is stock but fine, and mods are minimal.

It feels as if the plate/spring that stops you from shifting directly from 5th to reverse is still in place (i.e. possible failure).

I've booked the car into a transmission specialist....

Has anyone experienced a similar problem?

If so, what was the exact problem, solution and at what expense?

Many thanks in advance!

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/101495-manual-gearbox-issue/
Share on other sites
cowie165 Veteran

cowie165

Posted
Posted

Hi Phil

My symptoms were the same. It felt like reverse wasn't even there. SteveL helped me out and was 100% with his diagnosis.

The problem is most likely to be the spring (32185) has broken/fallen out and then part 32183 mechanically locks you out of reverse just like you have described. The lockout operation/type is common to most Nissan gearboxes so you don't really need to fuss over a 'performance' gearbox guy. That said, if you take it to a gearbox guy rather than a mechanic, you'll probably get away with it cheaper.

The guys I went to (have the number/address if you're in Sydney) removed the crossmember and were able to slide the gearbox back a little - just enough to access the reverse check assy on the passenger side, sorta behind the front pipes.

As the guys were able to move the gearbox rather than take it out, the cost was three hours labour ($165) rather than a gearbox R+R ($350+).

I hope this helps dude. The good news is that it's a fairly easy/painless fix (as Steve said) and the guys that would like to rebuild your gearbox in toto are probably just short on jobs at the moment. :P

Cheers

Mark

328-B02.JPG

R32GTS4 Apprentice

R32GTS4

Posted
  • Author
Posted

Thats fantastic help guys (SteveL and Mark)!!

:(

I've got it booked in for Monday. me hopes a similarly quick and simple fix.

I'll hand over the details to the transmission guy, and take the opportunity to replace gearbox oil with the (expensive but reputable) Redline Shockproof fluid.

Once again,

thanks Mark and Steve for help so far and I'll post up results early next week!

Until then, being wary of hills.....

Cheers :)

R32GTS4 Apprentice

R32GTS4

Posted
  • Author
Posted

All fixed! I had a small chat with the transmission guy before handing over the keys, armed with a printout of the same FAST schematic as above. The problem proved to be exactly the same as identified by SteveL and experienced by cowie165: broken spring (part 32185) which was locking me out of reverse.

I also had the helpful guys at Automac Transmissions replace the oil with a gallon of Redline Shockproof Lightweight Gearbox Oil.

Result? One full-functioning, smooth-shifting gearbox.

Cost was a very reasonable $85 for the labour/ parts (not including Redline Oil, which I bought elsewhere).

The gent. who replaced the oil said it was full/ dribbling at slightly under the 3.784L - which suggests to me that the R32 GTS4's gearbox has slightly lower capacity than the equivalent R32 GTR....more like the same capacity of the GTS-t.

Anyway, if anyone else has the same problem, I would suggest that you arm yourself with the same diagram to aid the mechanic, and they will hopefully be able to replace the spring mechanism in a similar fashion (removing the crossmember out of its place and sliding the gearbox back slightly - just as they did with cowie165's).

Very chuffed that it's fixed - and many many thanks to SteveL and Mark!

Cheers :lol:

R32GTS4 Apprentice

R32GTS4

Posted
  • Author
Posted

Up to me to pay it forward - lets hope the next person to experience this problem doesn't fret...... and realises help is but a click on the SEARCH button away...

A win for the forum i think!

Once again, thanks for your speedy replies and generosity....

:P

Cheers mate!!!

  • 3 months later...
R32GTS4 Apprentice

R32GTS4

Posted
  • Author
Posted

If I paid approx. half the price that Mark to have the identical problem fixed, I wonder what you'll pay?

Hopefully less again...

As mentioned, easily fixed by transmission experts.

I found that walking in with a pre-diagnosis (and above schematic) helped in this case.

good luck and let us know how it goes.

  • 4 weeks later...
  • 1 year later...
  • 1 month later...
=premo= Mentor

=premo=

Posted
Posted (edited)

same problem, hopefuly i get time to fix it before drift prac next weekend.

so everyone who has had this problem just bought the part, replaced it and problem solved?

nobody had a different issue. (dont want to pull it apart saturday morning to find its a bigger issue when i could have just got people to push my car whenever i need to reverse)

cheers

Edited by =premo=
CeJay Grand Master

CeJay

Posted
Posted

Well mine was no reverse, basically locked out, parts 2.50, I showed them the printout, they found the part. (nissan) took a week or so to show up. So if your reverse gear feels like it's locked out, that probablys the problem. Didn't do it myself. But been told it's not a gbox out job, isn't easy to reach though.

No probs with reverse since. Don't know if it's the same part on a rwd 32 gbox though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      First time we have seen lights 
    • Wazmond
      WGNC34 - floor mats

      By Wazmond · Posted

      I think Fitmit had some, have a look on there (theyre Australian as well)
    • soviet_merlin
      Howdy Y'all

      By soviet_merlin · Posted

      Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...