Jump to content
SAU Community

Recommended Posts

Anyone?

My turbo is a little poorly. :goddam:

I wouldnt mind knowing if the GTST t28 is similar to the GTiR one...

GTiR T28 turbo.

T-28, 60 trim 60 mm BCI-1 compressor in standard T-3

housing. 79 trim 53.8mm Inco T-250 turbine wheel .86

A/R turbine housing

ThankYou

Link to comment
https://www.sau.com.au/forums/topic/10163-r33-gtst-turbo/#findComment-159691
Share on other sites

I'll give you what I know.

The R33 (and R32 for that matter) has a turbo which has a bolt pattern of a T3.

So it will NOT bolt on to a car that had a T28.

The internals are of a similar size to a T28 though.

All I know about the sizes is that the exhaust wheel is 48mm for the R33 and 42mm for the R32.

But ALL skylines GTST from R32 onwards, have a T3 bolt pattern.

Not sure about the R31's and earlier..

The GTR's have twin T28 turbos. the bolt patter is a T28.

However, they are only good for twin turbo set ups.

The T28's on the GTR's do not work that good in a single turbo application.

WRXKILLA...

Just incase you didn't know.. the skyline turbos have ceramic exhaust wheels.. so I doubt that they would be an upgrade for your GTiR even if it did fit.

Link to comment
https://www.sau.com.au/forums/topic/10163-r33-gtst-turbo/#findComment-159798
Share on other sites

Nope,

The GTiR turbo will take excess boost pressures.

I know many GTiR owners that have run 18psi and even 20psi on the stock turbo for long long periods of time as daily drivers and never had a problem.

Of course it isnt exactly efficient at those pressures. But hey.

My Mate Ivan ran a 12.3 with stock turbo stock pretty much everything. 20psi.

My car came back from a Particular workshop withthe turbo buggered. Bit suspicious. Considering I had a lot of other things done wrong too.

But I was running 14psi.

Link to comment
https://www.sau.com.au/forums/topic/10163-r33-gtst-turbo/#findComment-160925
Share on other sites

nice...

did you go back to the workshop to complain or anything.

yeh the Gtir turbo's don't have ceramic exhaust wheels so no problem with running over 14psi.. but like you said, above that and it starts to get out of it's efficiency range... especially with the top mount interheater that they have.

Link to comment
https://www.sau.com.au/forums/topic/10163-r33-gtst-turbo/#findComment-160998
Share on other sites

he he he, yep, gotta love the Interwarmer, I cooked Bacon & Eggs on it once! :D

Yeah, Umongst other things, They Cross Threaded an Intercooler bolt and ross threaded the thread inside the plenum, (where it bolts in), left a gearbox bolt out!, replaced my Nissan Oil Filter will a Coopers!, I now get some clunking noises from drivetrain since the day it came out, and of course my turbo is a littel buggered since it came out.

I think I mentioned in another thread somewhre which garage this was.

In Sydney's East.

Link to comment
https://www.sau.com.au/forums/topic/10163-r33-gtst-turbo/#findComment-161051
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...