Jump to content
SAU Community

Recommended Posts

Hey guys, i just spat my turbo on the 33 and in a mad panic picked up a rebuilt one, the original had 45V3 on the compressor housing and the new one had 45V1, and had the compressor fins in pairs. Does anyone know if there are any other differences between the 2, coz the new one goes heaps harder

Link to comment
https://www.sau.com.au/forums/topic/101803-difference-between-v1-and-v3-turbos/
Share on other sites

Why did they change to the lighter nylon type wheel on the S2 and R34 turbo's then?

Not having a dig at all, just curious?

Two factors have a major impact on the rate of acceleration of an impeller:

radius

mass

Increase either of them, and the ability to build boost quickly is diminished.

Note that Blade numbers, shape, inducer size also impact on compressor performance.

cheers

Dale

  • 2 years later...

thats the same as mine..

ive got a '96 r33 series2..

i can took a photo of my compressor side..

i got a silver steel wheel..

single blades/fins wheel..

and it says 45V3 :)

so wat the deal?

can someone please explain??

i read that 45V1 & 45V2 is on series 1 R33

and that 45V3 & 45V4 are on series 2 R33

am i rit so far????????????????

then i was lead to believe that...

series 1 have a alloy single blade/fin wheel (is it alloy?or was it steel?????????????) :D

&

series 2 have a nylon twin blade/fin wheel

is this correct?? :D

As far as im aware the "v1" "v2" "v3" means absolutely nothing except the casting number. It has no difference between the numbers. My series 2 had a 45v1 on it and i can guarantee it came like that from factory. I now have a highflowed rb25 turbo and it came with 45v3 on the housing. Means nothing.

Are you sure you're not mistaking it for the black nylon series 2 wheel as it does sorta look like a metal wheel... Unless your turbo has been highflowed otherwise there would be no reason to change that wheel. It's the turbine side that spits anyway there would be no reason for the front to let go before the back.

And the series 2's still have a single blade from memory...

For all intents and purposes R33 S1 and R33 S2 turbos are virtually the same.

While the turbo makeup is actually different there is minimally noticeable difference in performance between them

R34 has a slightly larger rear on it (better for hi-flowing) and does make on average 10rwkw more @ 12psi than R33 items due to this

ah yeah i don't know anything about gtr turbo's but i would daresay they dont have the 45v"x" and would have something completely different as they're smaller turbo's and there's two of them. Sounds to me like he's talking about a gtst. Please advise.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...