Jump to content
SAU Community

Recommended Posts

need new tyres? buy these rims and sell your old rims!

Item: 17" sparco LT's w/ 8-90% tread Yokohama

Location: sydney

Item Condition: very good, no scratches / curb rash

Reason for Selling: need money

Price and Payment Conditions: 1400 quick sale

Extra Info:

Contact Details: PM here or email [email protected]

Actual rims:

finally.jpg

on old car:

20050814-R34S14-02.jpg

OFFSET is for GTR. Will fit Silvia's also.

Edited by Infamoz
Link to comment
https://www.sau.com.au/forums/topic/101919-17s-deep-dish-black-sparco/
Share on other sites

Yes they are multistud - and as you can see obviously fit onto Silvias and Skylines wit no problems.

The offset, I am not 100% sure, the tyres are 235's on all fours and look a bit stretched. All four wheels are identical, as they were off a GTR previously (hence GTR offset).

They looked VERY nice on my s14a with full vertex kit - very fat.

Edited by Infamoz
Yes they are multistud - and as you can see obviously fit onto Silvias and Skylines wit no problems.

The offset, I am not 100% sure, the tyres are 235's on all fours and look a bit stretched. All four wheels are identical, as they were off a GTR previously (hence GTR offset).

They looked VERY nice on my s14a with full vertex kit - very fat.

Without knowing the width and offset I don't see how anyone will buy them.

:P cheers :)

Yes they are multistud - and as you can see obviously fit onto Silvias and Skylines wit no problems.

By that do you mean they are 4x114.3 also, or are they 5x100 as well as the 5x114.3

180_mph, they are definately 5x114.3 because as you can see, they have been fit to an S15 and 14 no problems. For the other measurements, I really DO NOT know, but anyone can come try it out before they buy it.

I am in Sydney.

Shipping to melb would be around $150 I think, if you want to do that, then we can negotiate something, PM me and we'll exchange numbers.

Once again, all four wheels are exactly the same dimensions, rubber is very good, and they are 235/17/45 all around.

STILL FOR SALE.

Measuring the width of the wheels, it is approx 250-260 mm in width.

These wheels are doing nothing but sitting in my garage, they want to be put on a car and used. Somebody buy them, price is negotiable within limits - remember, it's basically got new tyres on them.

I am in SYDNEY.

Edited by Infamoz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...