Jump to content
SAU Community

R32 Gtr Heater Hoses

GTsauRus

By GTsauRus,
in General Maintenance

 Share

Recommended Posts

SteveL Mentor

SteveL

Posted
Posted (edited)
hi

my r32 gtr came with no heater hoses and my cd workshop manual doesnt show them.

I can tell the bottom hose at the heater  is the long one but at the motor end does it go to the block inlet or the pipe coming from the thermostat housing :P

thanx

As it happens I'm doing mine at the moment as I have the plenum off and decided to replace all the hoses so I only have to do this once (in theory). The heater hoses actually aren't all that expensive from Nissan (well I didn't think so anyway.

As you've probably seen there are two hoses attached (or should be in your case :D) to pipes that pass through firewall on the passenger side near the ABS actuator. The bottom of these hoses is the 'longest' - it runs behind the engine to the drivers side, angles down near the clutch master and then attches to a fitting at the back of the block above the starter motor. The second hose is actually 2 separate hoses that are joined at a sensor behind the motor near the ignitor box. It pretty much follows the same path as the first hose, but joins to a metal tube arrangement attached to the bottom of the plenum. The metal tube feeds into a fitting near the thermostat housing via another short rubber hose.

After all that I'd say it would be very difficult to replace the hoses without removing the plenum and it all becomes obvious once it is removed.

If you want I can give you the part numbers for the hoses and they're probably around the $100 mark for them all.

Edited by SteveL
GTsauRus Community Regular

GTsauRus

Posted
  • Author
Posted
ugboot do you have more pics of that 34 in your avatar?

sorry im no help for your question...

hi danh

i have more photos, its my 200mm nitro RC racer tho not a real 34 but it is 4wd 2spd auto makes 1.38hp at 38000 rpm I havnt raced it much since I got my gtr.

GTsauRus Community Regular

GTsauRus

Posted
  • Author
Posted
As it happens I'm doing mine at the moment as I have the plenum off and decided to replace all the hoses so I only have to do this once (in theory).  The heater hoses actually aren't all that expensive from Nissan (well I didn't think so anyway.

As you've probably seen there are two hoses attached (or should be in your case :)) to pipes that pass through firewall on the passenger side near the ABS actuator.    The bottom of these hoses is the 'longest' - it runs behind the engine to the drivers side, angles down near the clutch master and then attches to a fitting at the back of the block above the starter motor.    The second hose is actually 2 separate hoses that are joined at a sensor behind the motor near the ignitor box.  It pretty much follows the same path as the first hose, but joins to a metal tube arrangement attached to the bottom of the plenum.  The metal tube feeds into a fitting near the thermostat housing via another short rubber hose.

After all that I'd say it would be very difficult to replace the hoses without removing the plenum and it all becomes obvious once it is removed.

If you want I can give you the part numbers for the hoses and they're probably around the $100 mark for them all.

Excellent reply thanx

Im having trouble getting the long one onto the block fitting trying to do it from underneath after i moved the starter out of the way.

I bought hoses 1 long + 1 short =$96 and 6 plenum gaskets =$25 so i need the other short hose  plus the sensor(sensor joins the 2 short ones???) 

wasit easy to get the plenum off while in the car???????

I intended removing it but was gunna wait till i got a oil filter relocation kit. and do it all together

Ive got a couple of days wait for a new radiator so i wanna do the hoses and the timing belt while the rad is out but cant afford the filter relocation yet. then off for a run up to brisbane.

SteveL Mentor

SteveL

Posted
Posted
Excellent reply thanx

Im having trouble getting the long one onto the block fitting trying to do it from underneath after i moved the starter out of the way.

I bought hoses 1 long + 1 short =$96 and 6 plenum gaskets =$25 so i need the other short hose  plus the sensor(sensor joins the 2 short ones???)

wasit easy to get the plenum off while in the car???????

I intended removing it but was gunna wait till i got a oil filter relocation kit. and do it all together

Ive got a couple of days wait for a new radiator so i wanna do the hoses and the timing belt while the rad is out but cant afford the filter relocation yet. then off for a run up to brisbane.

There are inlet and and outlet hoses to the heater core at the firewall. One of them is a single long hose, but the other is made up of 2 shorter hoses joined by the sensor. Nissan sells the hoses individually, so there are 3 hoses + the sensor. On top of that there's another short hose near the thermostat (you probably can't even see that one.....if it's there in your car (??).

Plenum was easier to get off than I expected, but still fiddly. The 'secret' is to unbolt the small 'sub' plenum from the main plenum (the 'sub' plenum has the AAC valve attached - in fact it's best remove the AAC valve first). You also need to disconnect the fuel pipes plus a few other small bolts attached to the bottom and side of the plenum - all good fun as it has to be done by feel (ie blind). I also found I needed to use a range of 12mm spanners and small sockets to get the plenum nuts undone.

I'd recommend doing all the hoses, etc after you take the plenum off.

Heater hose PN's:

92410-05U00 - long heater hose

92402-05U00 - hose from engine to sensor

92401-05U00 - hose from sensor to firewall

27724-05U00 - sensor

14055-05U11 - hose at thermostat housing

danh Community Regular

danh

Posted
Posted
hi danh

i have more photos, its my 200mm nitro RC racer tho not a real 34 but it is 4wd 2spd auto makes 1.38hp at 38000 rpm I havnt raced it much since I got my gtr.

ohhh man thats hot! haha

it looks like the phattest wide body 34 in the pic!

well if you wouldnt mind sending me that pic u have in ur av, to

[email protected],

cheers mate

Dan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...