Jump to content
SAU Community

Recommended Posts

Hey every1.

I was driving around a bit yesterday and had the aircon going pretty hard most of the day. Last nite was on chapel st when some hose under the engine broke and water started gushing out. My car started overheating and revving higher on idle so i stopped luckily in time before the temp reached into the red (it reached about 3/4 of the way up). I opend the radiator and empty, a bit of steam came out and thats it. Underneathe the car there was a loud hissing noise from the water hitting the exhaust i think. It seams to be coming out of the area around the back of the block/dump pipe area.

My mate reckons its prob the heater hose that has broken since i was using air-con all day. (pretty easy to fix i heard)

What i am concerned about is if its the coolant hose to the turbo that may have broken. ( i have just had the turbo refitted since the gasket needed replacing) If so its prob the mechanics fault for not fitting it properly.

Now this i dont mind (replacing the coolant hose shouldnt be an expensive problem). What i do care about is if my engine/turbo have sustained any damage as a result of this event.

Any experiences/advice much appreciated

Taso

Link to comment
https://www.sau.com.au/forums/topic/102826-burst-water-hose/
Share on other sites

I had my friends dad look at it 2nite, he couldnt locate the problem but said that it was coming from somewhere behind the gearbox. Is this where the heater hose is located.

Its leaking really bad, the entire radiator is basically drained after a couple of minutes, i'm gonna havee to have it towed to the mechanics i think coz i dont want to cook the engine. (Malvern to Oakleigh)

Is this a common symptom of a failed heater hose?

Rad/heater hoses have a habbit of letting go during the hotter weather.

When it dries look for white stains caused by the coolant.

Yea thought that might be the case, I guess in Japan they don't have 40+degrees, bloody Melbourne weather!!

Chances are its one of the little hoses located around near the back of the head - under the plenum. A real pain in the arse to get to. :S

Its not so much the 40degree heat but more so the age of the car.

When one starts going they soon all follow.

My little U shaped hose that runs around the back of the head went, then as it was only a small leak I left it and waited until the new motor went in, THEN the little hose that joins the pipe work that connects to the in manifold went, when pulling it off I noticed there was another little hose that connected to the block that fed in to the heater hose, that too was stuffed. ;)

My little U shaped hose that runs around the back of the head went, then as it was only a small leak I left it and waited until the new motor went in, THEN the little hose that joins the pipe work that connects to the in manifold went, when pulling it off I noticed there was another little hose that connected to the block that fed in to the heater hose, that too was stuffed. :P

Worst case scenario, if that happened to my car, how much $$$ do u reckon i'm up for. (If anything connected with the manifold/turbo is broke i'm gonna skitz it at the mechanic cause they just refitted it)

You can't skitz at the mechanic if a ~10yr rubber hose has decided to sh*t its self. :)

BUT.. that being said he shouldn't charge you for labour as he should have had a look and feel of the hoses being refitted.

Most mechanics don't give a sh*t and simply refit everything back up.

The ones that do and call you up saying this is stuffed thats stuffed generally end up being viewed as a mechanic thats trying to make more $$.

No win situation. :cheers:

Edited by Cubes

turbo feed hose went on mine.. pain in the ass to change too cos there is no room.

best way to look is to fill it back up, and see where is leaks from.. with the engine off so you its easy to get in there and see.

oil feed to turbo would help protect it and keep it coolish

turbo feed hose went on mine.. pain in the ass to change too cos there is no room.

best way to look is to fill it back up, and see where is leaks from.. with the engine off so you its easy to get in there and see.

oil feed to turbo would help protect it and keep it coolish

That is what it ended up being, took mechanics bout 30min to fix.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GCG is a good company, they're a major distributor for Garrett in Japan as well.
    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
    • Ok thanks 🙂 I will higly consider this. Any "known" company for a good reviews and experience to send that off? Is that CJ-motor good one? Or go straight to GCG site? I need to use VPN to even find some of those "shops" let alone access them 🙂 
    • You can literally put in as much WMI as it takes to quench the combustion totally (and then back it off a little, obviously), and it will keep making more and more power. The power comes from the cooling effect of the water (and the meth) and the extra fuel (the meth, which also has massive octane). It is effectively exactly like running E85. One might be slightly better than the other, but they are damn close. But with either you can lean on the boost or the timing (or both) waaaay more than with just petrol and the results are similar. Here's the first thing I googled for an anecdotal bit of evidence. Can't access the attachment without being a gold member, but it is there for the getting if able to, or searched up elsewise perhaps. https://www.hpacademy.com/forum/general-tuning-discussion/show/wmi-vs-e85/
×
×
  • Create New...