Jump to content
SAU Community

Recommended Posts

Hi Ben

My car hasn't been started for over a week so I'm keen to come down if just for the drive. Sorry to be a pain, but what are the times again please?

And you take the first WSID turn-off? That's the one for spectators and the second one (where everyone met for the SAU Drag Day in Nov) is for competitors?

:D

what are the times again please?

Gates open for competitors at around 4:30ish, racing starts at 6pm, burnouts at about 9-9:30ish and racing is over by about 10-10:30ish (and considering its the Holden vs Ford day the following day it should be until about midnite i reckon, would get heaps more runs in).

1st turn-off (back entry for EC Circuit) is for spectators. The 2nd turn-off is for competitors, as Moooanie stated.

Edited by benm
kool man can i ask ur ezact mods for a guestimation of that time?

thats what im afta, i have a r33 gtst also

just wanna see if my mods catch urs

Sweet.Well i will come say hello to all i see.

As for the mods stock turbo,11psi,pfc,fmic,stock airbox hiflow filter,hks style dump to 2.75 pipe to 3''cat and 3.5'' thereon,h/d clutch.

Last time i was out i ran a 14.2 with a slippn like a mofo clutch a baby fmic and pod filter.

WSID website doesnt say anything about it being cancelled

the weather says:-

For the remainder of Wednesday

Overcast day with isolated showers and drizzle, clearing during the

afternoon. Light to moderate east to southeast winds.

Precis for Wednesday Max

Sydney: Shower or two. 23

Liverpool: Shower or two. 23

Penrith: Shower or two. 23

Richmond: Shower or two. 23

Tonights Auto One Wicked Wednesday Event Cancelled Due To Weather

Wednesday, 31 August 2005 - Posted by Dean Neal

Wild winds and threat of rain have caused the cancellation of tonights Auto One Wicked Wednesday Action (Pic: Peter Colburn)

(Sydney, NSW) Due to wind gusts regularly exceeding 90kmh today in the Sydney area and at the Western Sydney International Dragway, coupled with the impending threat of rain this afternoon and evening, tonight’s Auto One Wicked Wednesday event has been cancelled.

Such is the severity of the winds, display signs have been blown off their chains around the venue today!

“We have obvious safety concerns with the prevailing weather conditions and thought it wise to cancel tonight’s meeting. However we will be back in action with our off-street Drag Racing events as per usual next Wednesday night,” remarked WSID CEO Jim Read.

Tonight’s exciting ‘wicked’ mix of off-street drag racing, burnout competitions and Heat 3 of Miss ‘Wicked Wednesday’ thanks to Provocator Jeans and Auto One, will now be contested NEXT Wednesday Night (September 7).

For more information, please contact the Western Sydney International Dragway on: (02) 9672 1320 or [email protected].

Umm thats from August 2005.

It's still currently on (as shown on www.wsid.com.au), they always put up a message when it has been cancelled (last update is usually 3:30pm).

So at present it is still on tonight!

Jan 25 , 2006

Gates Open 5pm, Racing from 6pm, Burnouts 9pm.

1:20pm Update: Persistent rain in the area, Wednesday event Postponed. All Street Meet competitors please be aware you can race in tomorrows Holden V Ford event if you possess a Holden or Ford vehicle and enter on the day (tomorrow morning).

:( :( :( :( :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...