Jump to content
SAU Community

Recommended Posts

firstly can i say what a fantastic forum, information on here is priceless.

im a gts owner from across the water in the UK and very impressed with this set-up . and reading through learning stuff i never thought id learn.

i posted this same topic on the uk owners club, but the response i got was very poor and im hoping maybe yous can help me out

------

c5_1_b.JPG

bought this from ebay.

its in excellent condition apart from this one sided crack.

im planning on repairing it myself ( hopefully ).

can someone or everyone offer my advice on how to, what to do etc etc.

this is the first time ive ever tackled this, and being as brave as i am, my next purchase is a bumper thats needing similar patching up.

i dont believe in paying a body shop to fix something im sure i can manage myself with a bit of time and effort.

Link to comment
https://www.sau.com.au/forums/topic/103344-body-work-maintenance/
Share on other sites

plastibond!

Don't know whether they have it over there, but for that sort of smallish job, that is what I would be using. Its basically a two part epoxy (I think!) paste that you mix up, and it hardens to a fibreglass type strength.

After that you can get the sandpaper out and smooth it out, so that it follows the original angles.. bit of paint and nobody would know.

I've used it to repair small cracks in front bars, and its much easier than using fibreglass for small work.

Yeah my answer to everything like thast is BOG lol BOG it up and sand it back then paint it, i'm not fimilar with Plastibond, but predator makes it sound like its a better bet. Bog is what they use to patch up crack dings in basiclly your body kit (hopefully not all over your car LOL)

But yeah bog is really easy to use, once again its 2 parts, its liek 1:50 and you only add a tiny bit of hardner, it goes of in a few mins so you only mix a little up at a time and then you will be sanding for a while LOL, Bog sets like concrete and is what i would use if i was in your situation (only cuase im fimilar with it, not saying it's the best method)

I hope it helps

Michael

Bog is a product used by panel beaters. Ive used it to make flairs on a RX7 S1, and its a very very easy product to use.

All as you need to do is sand back the area lightly to remove the paint, make sure there is so oil or dirt where yrou goign to bog, so clean it up. Then once you mix the bog, as i said its two parts, you got you putty, then the hardner, mix it up, it'll say on the packet what coulour it shoudl go, then jsut smear it into the crack with a scraper or ne thing really, smooth it out as best as you can on the out side, then leave it 10 or so mins to dry, and start sanding back the bog untill you get the shape you want.

As for sandpaper yeah wet and dry will be fine, use a normal gritt one to take the paint work back, but use a heavy grit for takeing the first few layers of the bogged area you have just done, once its getting down to the shape and leveling out with the other plastic, use a finer grit so you get a smoother finish, then last set is jsut painting.

It's very very very easy, you will be fine.

Bog is basicly an automotive putty, that sets like concrete.

Hope i'm of some help.

Michael

ah bog will be what we have as "body filler" over here?

http://www.diytools.co.uk/diy/Main/Product...ProductID=11889

thanks michael, youve been a great help. hoping to get started on it tommorrow.

but one final question ( please dont think im daft ), would i be best to remove the mesh before i start this?. its just the screws holding the mesh seem a bit rusted and it may be tricky. but im half saying to myself, "dont be lazy, do this right and remove the mesh, dont skip bits, do it properly".

That looks like the stuff, i just had a 5kg tinn LOL and a tube of hardner, you only need a little bit however.

As for the mesh:

Too tell you the truth by the looks of the picture you don't really need to take it off, i mean the crack are on the out side and the mesh doesnt' really get in the way, however it could become a problem when respraying. You can leave it on if you want.

Personally what i would do, is take it of, either buy new stainless stell mesh if you want silver or stick to what you want, replace the screws with stainless steal so the new ones don't rust, or if its black grill, just paint the stainless ones. Also if you take the mesh back you can easily sand back the "whole" grill, giving it a complete respray, then replace the grill back on with either the old grill or new grill, and new screws.

Thats what i would do.

Be sure to post pictures of your work.

Michael

Edited by Michael_1882

BOG is just polyester resin loaded with a filler like calcium carbonate( talc ). To get the best adhesion to do this repair it would be best to use straight polyester resin. Just check the back of the grill and see if it aint ABS plastic as well. If its ABS or fiberglass youll be ok with the polyester resin for the repair. Just wash it with soap and water and then clean it with acetone to prep the surface before you start the repair. To get polyester resin and hardener go to fiberglass repair places like boat shops or swimming pool places. Follow the instructions and youll do fine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL, when one "money pit" is never enough Noice, and excellent work mate
    • I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
    • I hear that would involve some nice country road drives into the hills for Mark...
    • I thought I'd come back and add something I JUST learned. A Toyota LandCruiser with a 1HZ, mates perfectly with a bottle of Nulon brake fluid. As in, it perfectly screws in. Great make shift funnel when you cut the bottom of it off. This may work for your Corolla.   Unfortunately, tipping a 10L drum is much harder than a 4 to 6L bottle, and they no longer include the easy pour tap which was just perfection to use previously.  
    • Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
×
×
  • Create New...