Jump to content
SAU Community

Recommended Posts

Hey every1, this is my first post. I've been into fords for a long time and know alot about them but i've realised how expensive they are to make fast compared to skylines and how skylines are much better in handling, fuel efficiency etc.. I'm thinking of getting an r-33 cause i've always liked the shape and either a gts or gts-t. Because I know practically nothing about skylines, i need your help. Firstly, what kind of performance figures would you expect from the gts/gts-t. Also, between the automatic and manual transmissions, is there much loss of power through the automatic drivetrain compared to the manual? Thanks, and any other noob tips for me would be greatly appreciated. :P

Link to comment
https://www.sau.com.au/forums/topic/104038-im-new/
Share on other sites

....any other noob tips for me would be greatly appreciated.  :P

Skylines are made by Nissan in Japan ;) :lol:

Nobody 'wants' a non turbo Skyline but it just sometimes works out that way because of the cost. A decent R33 GTS-t should set you back a cool $16,000....less if imported.

And remember, use search before asking questions. No n00b can be told a more useful thing B)

Welcome to the club ;)

Link to comment
https://www.sau.com.au/forums/topic/104038-im-new/#findComment-1913613
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...