Jump to content
SAU Community

Recommended Posts

ok i was giving my R32 GTR a bit of a flog (as you do)

just come out of one corner and heading to the next and was about 5k in 3rd

then POP (a jolt of deceleration) so as you do you go into What The F@%K mode

then after that i find it still idles the same and drives the same until.....

about 3k (where boost usually is) and it begins to sorta cough and pretty much wont rev any higher

i am yet to pull off the exhuast to look for remains of turbo in cat (as it happened JUST now)

just want to make sure that it sounds like my turbo and i havent done any Major damage

and i have done a search and couldnt find anything is anyone else finding the search not really doing it job anymore?

Well Damn!!! ....but it looks like its could be time for some GT-SS's

Thanks

RellikZephyr

Link to comment
https://www.sau.com.au/forums/topic/105201-did-i-blow-my-turbo/
Share on other sites

pop and then coughing and spluttering, are you sure the plugs are on the air flow meters firmly, done that one before, car went into safety mode over a speed bump when the plug fell out, wouldnt rev over 3k lol...

having said that, i have also blown 2 turbos, tap the cat and see if there is a rattle like noise, also mine backfiered heaps when i blew the seal in one of the turbos, then no boost when i blew the wheel off the other one :P

Edited by oRiCLe

you guys are absolute CHAMPIONS!!

i didnt even think off intercooler hoses

and it was an intercooler hose passenger side on cooler to be precise

Thanks a bunch you guys i was shittin!!

Champions Thanks again

RellikZephyr

I would check your AFM too. When I had a VL (dont hold it against me :) ) The same thing happened. It made a really load pop (i found out later it was just a huge backfire) and after that point the car would get to 2000rpm and not go any higher. Changed the air flow meter and it was good as gold.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...