Jump to content
SAU Community

Recommended Posts

Hello all, just a quick question i did a search but couldnt find anything, i want to paint my calipers but im just wondering do you have to bleed the braking system once you take the calipers off or can you just put it back on and just drive. Also could i just take the front of the caliper of and not bleed it. Any help is appreciated thanks

Link to comment
https://www.sau.com.au/forums/topic/105331-brake-calipers/
Share on other sites

You'll be able to tell if they need bleeding as you approach the first corner!.

Generally, if you disconnect the brake lines anywhere, you will introduce air, and you will have to bleed the brakes.

Link to comment
https://www.sau.com.au/forums/topic/105331-brake-calipers/#findComment-1940445
Share on other sites

Mask the surrounding areas and you wont have to disconnect the brake calliper.and if you are going to light sand it do it while it is on the rotor and blow sand away and clean.

Are you painting both sides??

If you are only doing one side of the calliper then you could do as i said and leave it on the rotor!

Go to the diy section and if you cant find it by just looking do a search in there.There is somthing wrong if nothing comes up on the topic.

Link to comment
https://www.sau.com.au/forums/topic/105331-brake-calipers/#findComment-1940641
Share on other sites

thanks guys umm i think ill try and just do one side of the caliper so i dont have to disconnect the brake lines but if/when i get bigger wheels and it looks funny then ill have to disconnect it and do it properly ill look in the DIY section and see what i can find

Link to comment
https://www.sau.com.au/forums/topic/105331-brake-calipers/#findComment-1941885
Share on other sites

It may be a good idea to disconnect the brakes and DIY overhaul the calipers. They would probably appreciate the freshen up and you can DIY for under $150 rather than pay $500 for a workshop to do it.

Plus it makes painting the calipers a whole lot easier! :P Bleeding takes about ten minutes to do it once, do it right. I've found that the 'one-man bleeders' are useless and that it takes two of you to do a proper job first go. Much faster too.

Link to comment
https://www.sau.com.au/forums/topic/105331-brake-calipers/#findComment-1942678
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...