Jump to content
SAU Community

Recommended Posts

to the 1% of guys with an auto box, do you guys know where to fill up an r32 auto box with transmission flluid?? my friend thinks the power steering tank is the same as the auto one, is this true??

Nissan normally spec Dexron III ATF, choose a good quality synthetic ATF like RP max-atf or Redline high temp atf will do you good in the long run.

r u talking about an r33? cause the only thing on the left closest to the firewall behind the strut tower is the brake fluid bottle, and i cant find any yellow dipstick besides the oil one in the engine bay, does anyone know where i can fill atf on an auto r32 rb20det?? trex101??

r u talking about an r33? cause the only thing on the left closest to the firewall behind the strut tower is the brake fluid bottle, and i cant find any yellow dipstick besides the oil one in the engine bay, does anyone know where i can fill atf on an auto r32 rb20det?? trex101??

Nope, got no idea.

thanks guys for all the help, since were all on the money i got another issue, mines full now but still doesnt change gears occasionally leaving the lights, i need to switch the car off and turn it on again for the gears to work, auto specialist reckons i need a full service for about $200 he vacums out the inside, could it be an electrical fault however??

...my fluid is very clear

Thats normal.

and very low

To get the correct level reading the trans should be at normal operating temp, so go for a drive around the block couple times & during which you should manual shift through the gears. Then with the engine still idling check the fluid level as you would with the engine oil. So if u checked the level while its still cold it prob showed it was low, so lets hope u didnt overfill to much.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...