Jump to content
SAU Community

Recommended Posts

Here's mine, I went through home at lunchtime so I e-mailed it to myself at work

The engine isn't in an R34, it's in an R31 but it's much of a muchness I guess.

Only mods are a full 3" mandrel exhaust from turbo back (non split dump) and high flow cat, Just Jap 600x300 FMIC and a Blitz pod. Stock boost and stock ECU.

It's pretty similar to yours, I wouldn't be worried that yours is weak or anything.

Was yours dyno'd in 4th gear?

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

You should have dynod car before you modified it, then you would no if you made any improvement, probably best not to shoot your mouth off as you have no idea what car made in stock form. if you are seeing an extra 2 pound of boost, the exhaust mod is clearly working. Put some boost in it and the dump pipe will come into its own.

Oh so I am making 10psi with this setup? Fair enough then, no need for EBC or boost tap then haha

I know its a linear curve and all which is good for a stockish car. I dont have a pod, just a apexi panel filter. And I dont think Im making 25psi, I believe its 10? Correct me if I am wrong hahah And with regards to BATMBLs pipes, doesnt seem like it made much of a difference, maybe its just my setup but the 16rwkw claim for the dump pipe alone just doesnt add up with my sums.

I expected:

10-15 from the split dump

maybe 5-10 for the cat

and another 5-10 for the cat back.

So worst case should be a 20rwkw gain, best case, 30ish??

I heard somewhere that for every 1PSI of boost wound up; it works out to being 11rwkw more :)

I'm running 200rwkw on 7psi now; can't wait to wind it up to 18psi :)

As people have said, just crank up the boost!

  • 11 months later...

Yes, it's an old thread, I know, I was looking for something else entirely (looking for dyno graphs from a certain workshop to compare with)

Anyway, I noticed on the first dyno graph that has been posted, the car has been run in the wrong shootout mode. This WILL affect your power read out.

The car should have been run in Shoot_6F, not Shoot_6.

This affects ramp rating, and internal measurements etc.

I didn't really wanna add to this topic since it's an old one, but how/why is the whole "should have been run in Shoot_6F, not Shoot_6" going to make such a difference, exactly? (without repeating the ramp rating etc - just a clearer answer)

Edited by so_tred

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...