Jump to content
SAU Community

Recommended Posts

cant believe ir just read 13 pages of all this

1.4 sixty foot and 129 mph and only a 10.8

you need to changes gears faster that thing will go 10.1 with ease.

or get an auto.

good work i like it.

our cars would be a good match up.

Yeah love to champ

Reason why i didnt flat change is the scared to blow the box and thats useless money

I have just finished putting the auto in and have driven the car but have noticed i have only got around 4-5 psi of boost

I am going to check this problem out and Do a comparence dyno printout from Manual To auto.

The box i am running is a 2 speed powerglide with transbrake.TCT Converter With a mech Diode

I have also got a Chrome moly 1 piece tailshaft made to help with the transfer

I will post tomorrow the difference and will be back at the track in 2 weeks

My next aim is to run in the 9 second area.If it cannot be done with the standard head which i think is possible with some Nitrous but if not i will use the Solid lifter head which i have got with a steel head gasket.And that also goes if the head gasket goes i will also change heads.

Edited by MR331307
I cant believe that rb25 is still going. I hope my rb30det can make 400rwhp in stock form and be reliable!!! if that rb25 can do then mine can get close to it im sure :cheers:

Hey Guilt-Toy, I have an internally stock (apart from poncams) rb25 making 410.7rwhp and it is running fine. It is on a conservative tune with timing advance and a/f ratios to keep it running as long as possible. But then again others running less have had the motor pop. I guess a lot has to do with the tuning and the condition of the internals to begin with.

Cheers,

JB

Ok have run the box in a bit on the dyno and have done 4 power runs

Without modifying the tune i have made 477 WRHP with the auto on just 18 psi Boost

Before the auto i was making on average 500 RWHP on 18 psi of boost on pump fuel

I will post the nitrous compared sheet next week when im back from Newcastle as well as this sheet

But as far as what i can see i only lost 23 RWHP

I also tried to spool it on the brake and found it couldnt get more then 3 psi

I tried with the nitrous and it flared straight away

This is due to the converter being a Transbrake Nos setup converter

The converter Was built by John @ TCT in melbourne which i think did a unreal job and the box was built by Joe @ Wollongong Automatics.

I should be back at the track in 2 weeks now

Waiting on the car to be teched.

My aim is to run in the 9 second area and further till something gives way.If something does i will change motors and try eventually to run into the lower 9 area.

Any questions just ask

Edited by MR331307
1200hp would be good for 8's or 7's wouldn't it? whens the beast arrive?

Im using this engine in my Full chassis car that my father and i am building

Im using the other engine i have in this one

the one with the solid head ETC

i do

but i am not allowed to Show the Setup

(FAMILLLLYYYY MATTERS)

when its closer to being @ the Track ill post some photos of it and the car

This is what is in the Motor im putting in this Car

-RB26 Crank

-N1 oil Pump

-EAGLE H beam Rods

-ACL forged Pistons

-ARP main & head Stud kits

-Cometic Head Gasket

-RB25 Head with TOMMIE Valve Springs,Solid Lifters,Tommie 272 @ 11.5 lift Cams

Aiming For 600 RWHP+++ and a low 9

Edited by MR331307

hey bro, look ive just spent the good part of 2 1/2 hours reading this thread and its my bloody birthday, ive even held of on the cake till i read this, lol. What a thread, one of the best of read on this site. To the doubters out there, well you said he was dreaming and the dream came alive. The power you got out of the engine was pheonaminal, it makes ya think what a 13 odd year old engine can actually achieve. To the believers, aim high and you can go far. I know that the availability of a dyno and the mind of someone like your self (mechanicaly) not everyone has, but you took advantage of it and done well. That engine had a lot of balls. Anyway good luck with the new one and who knows what power you'll hit with this one.

Damo

hey bro, look ive just spent the good part of 2 1/2 hours reading this thread and its my bloody birthday, ive even held of on the cake till i read this, lol. What a thread, one of the best of read on this site. To the doubters out there, well you said he was dreaming and the dream came alive. The power you got out of the engine was pheonaminal, it makes ya think what a 13 odd year old engine can actually achieve. To the believers, aim high and you can go far. I know that the availability of a dyno and the mind of someone like your self (mechanicaly) not everyone has, but you took advantage of it and done well. That engine had a lot of balls. Anyway good luck with the new one and who knows what power you'll hit with this one.

Damo

LOL HAPPY BIRTHDAY BRO

Anyways ill post some picts of the Internals

If i wasnt Selfish and didnt try to get more power out of it i would say it would of Lasted alot longer but i was always Trying to make more instead of leaving it

Anyways

Shouldnt be to long

Cheers mate, but also in saying that you were selfish, you also did something that im pretty sure a lot of people have always wanted to do but have never had the balls or money to do, run the bitch as hard as it could do and not care about the consiquences, i think a lot of poeple will actually understand that the more you look after the car, the more power can be put into it. In saying that, within reason ha ha.

Damo

After all the Motor Has been through i can say that it is possible to Make 470 RWHP safely on a Street RB25 Standard motor and make it last on Pump Fuel.

To make even more Safer power i recommend Changing the Head Gasket to a Tommie or Cometic and Upgrading Cams in which you wont have to Run as much Ignition Timing and Boost.As for the Bottom end i think that all of it can last.

The main Reasons for the Car making the power is

1) suffiecent intercooler (this is what Makes your Power And makes the Engine last Due to A stable Low Air Temp)

2) the Design Inside the Plenium

3)A Efficent Turbo (there is no need to Get a 1000 hp turbo if all your looking at is 600 engine HP)

4) Great Ignition Setup which is pretty basic and can get even better like the Next setup im doing which runs 6 coils

5) A good ECU

6)Reducing Load Off the Engine EG Clutch fan

7) good Fuel Supply

well done mate its lasted alot longer than the knockers on here had imagined. bout time someone showed em they are keyboard mechanics and dont actually know from there own experience, just from "i heard ..." and "i reckon ..." comments said on forums.

good luck with the new setup

well done mate its lasted alot longer than the knockers on here had imagined. bout time someone showed em they are keyboard mechanics and dont actually know from there own experience, just from "i heard ..." and "i reckon ..." comments said on forums.

good luck with the new setup

Thanks Mate

I havent commented yet and thats becoz I know f**kall about what destroys a good motor at that amount of power, but its interesting to note that it was No6 that lost compession, as that piston seems to be the one that cops it alot, higher temps and first to lean out, have you accounted for this in the new setup?

And Oh well done I would be happy to have your dyno hours :(

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...