Jump to content
SAU Community

Recommended Posts

Can anyone recomend any body kit suppliers in perth, all i need is a front bar and something on the rear for my R33, i had my eye on a bar from one supplier, but dont know if its against forum policies to mention names and ask opinions?? :(

anyone have any recomendations??

Cam

Link to comment
https://www.sau.com.au/forums/topic/10699-body-kit-suppliers-in-perth/
Share on other sites

Guest KILLER-T

Go to Works auto or is it Auto Works in bentley i allways get them mixed up:confused: anyway i went looking for a front bar and they had the best quality kits by far.The thing i liked most about them was the thickness of the fiberglass nice and thick no chance of warping in the sun :uh-huh:

all i am after is a nice front bar, nothing too over the top like a veilside bar, just neat and looks better than my UGLY standard one, some of the 400R look-alike ones i have seen look good, i do know alot of the places that supply them, but just not sure of the good ones.

hehehe, me a bitch?? im gonna go sit in my corner and cry now :D

hehehe, nah i was meaning the really OUT THERE veilside fronts, i have seen your one and it is nowhere near like the other veilside ones, hey i never even knew it was veilside bitch........ :D

(oops, im back in my corner) :lol:

400R front and i think they are 400R rears aswell, the rear is just the pods that stick on to your existing bumper, i already have 400R sides and a GTR wing, just gotta wait 2 weeks for the pods to come in and then get it all fitted up, works auto took care of it all, so its much easier than having to find a painter to paint them after ya get them...

Cam

paul:

i think i mite cancel it now that i know your associated with the painting side of things, just jokes :) better be a good job, its gonna be a hard one to colour match i rekon :D

Dan:

ummmm not to sure, cause it was just a all up price for the whole lot, fitted and painted, but i think the pods were about $120-$160 just supplied not painted and fitted, but there nice pods, they had 2 different types of pods, i saw the ones that you see alot of around but they had these other ones that were a bit bigger, made it look a bit fatter, so i went for them.

Riaz:

if ya still wanna take a look at the bleeder thats kewl, but still wouldnt mind seeing the bumper just to see what kind of job they did for future reference. but whenever if ya wanna wait till next cruise or so, thats kewl

hope i didnt miss anyone :lol:

Cam.

Cam,

No, I'm not painting them, but the owners of Works Auto have a paint shop associated with them, so you can alwyas get stuff done via the one place.

If you want me to paint it I will, but I wouldn't count on how good it would look.

See'ya:burnout:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...