Jump to content
SAU Community

Wheel Fitment

Hella Flush

By Hella Flush,
in Four Door Family & Wagoneers

 Share

Recommended Posts

adrnln Proficient

adrnln

Posted
Posted

rear will depend on also what brake set up you have.I have converted to a 350z rear brake conversion, with 2 pot calipers on the rear and have difficulty finding rims to suit.

The silvia tear drop rims dont fit but the 7 star ceffy,silvia,180 rims miss the calipers.

Ive found anything with a 30+ish and up offset I can use.

Link to comment
https://www.sau.com.au/forums/topic/107416-wheel-fitment/#findComment-1981878
Share on other sites
Resin Rising Star

Resin

Posted
Posted
offset of 38 works fine until you get coilovers which make the offset sink in! ;)

lowering without additional adjustment will create neg offset on rear ....i think mine has just over neg 2 degrees ......i have 17inch ... 8 inch +30 work meister s1's on the front and 9 inch + 35 on the rear. stacks of room around the brakes for future upgrades. They only scrape on the plastic crap on the inside of the gaurd at the front. +30 is max really for stock gaurds on the front. mine stick out about 4 to 5 mm .....

Link to comment
https://www.sau.com.au/forums/topic/107416-wheel-fitment/#findComment-1982285
Share on other sites
RiverSide Proficient

RiverSide

Posted
Posted

My old Orange ceffy had 18 x 11" rims on the rear........i am very UNcertain of the offset but i think it may have been -20ish.

There was about 7" of dish.

Obviously anything like that won't fit a vehicle that does not have the crazy/stupid bodymods that were carried out on that car.

Link to comment
https://www.sau.com.au/forums/topic/107416-wheel-fitment/#findComment-1997096
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...