Jump to content
SAU Community

Recommended Posts

get a Ninja Case :laugh::D

http://www.pccasegear.com.au/prod3033.htm

somthing like this PSU will do fine no need to go over the top that GFX card doesnt even run its own molex

http://www.pccasegear.com.au/prod3598.htm

i just remebered b4 ive used this ebay seller is very prompt and is in adelaide to

Ebay PSU

EDIT

Vista Home Premium

i bought a copy of XP of him and bould buy more things

EDIT

Mobo CPU and Ram combo

Edited by Madaz

so, i has a small problem.

well, a few small problems.

1. my connection speed is as low as 1mpbs. (using a belkin 54g, a few hours ago it wouldnt connect, period, stuffed if i know how i managed to connect).

2. most of my usual sites load, with the exception of the r31skylineclub... and i know that isnt down.

so, any suggestions and such?

A few things to try off the top of my head...

Power off/on the modem

-If sync/speed is still bad disconnect every phone in the house from the phone line and power off/on the modem again and check sync speed.

--If it improves you know you have a dead line filter (not common but does happen). Isolate the dead line filter by connecting a single phone at a time and calling it with your mobile while watching for sync/speed drops and transfer interuptions.

Are you on ADSL2?

-Change your line profile to a 'reliable' profile to improve stability as they ncorporate interleaving which as a result increases ping so not so good for online gaming but its better than having poor stability.

Changing the line profile to reliable profile works well on those wet days where water gets in to the lines causing a little cross talk that results in poor stability/reduced sync speeds. I've had to do this almost every winter :whistling: Then wait for telstra to get out and fix the lines. In the last recent downpoor the phone line dropped out completely, unable to receive or make calls (no dial tone with lots of crackling and static) I called internode had them throw me on the very high reliability line profile and I connected at just under 1mbps. It took 3 days for telstra to sort out the problem. :S

and ....... Call your ISP. :)

well, unplugged all the phones and such, the connections a little better, but its still slow (>12mbps) and its still fairly unstable, but its better than it was 10 minutes ago, ill call belkin and internode tomorrow and see whats up.

i doubt its internode though, looks more like the routers f**ked, had so many problems with it...

Linksys, Billion & cisco (out of reach) modems for me. I prefer billion modems.

Always have a quick look at

http://cgi.internode.on.net/advisories/list.html?area=1

to notify of any issues.

Most likely the telstra line that runs from the internodes hardware in the exchange to your modem/router.

In the meanwhile if transfers web browsing and transfers are unstable throw yourself on a more reliable line profile (done via internodes web site and monitor when the modem resync's on its new more stable line profile)

You should be fine with the high reliable profile, very high profile may be a little overkill.

Failing that do the usual virus scan & spyware/malware scan.

spyware/malware - lavasoft adware, spybot and the VERY usefull prevx1.

If your familiar with services that are supposed to be running hijackthis is also a handy tool to use. I tend to use all three on problem computers.

try looking @ a Mitac EL80 one of my mates bought one and he was very impressed there is also overclockers AU did a review and other boards that you can google

i had links for you but i dont know what happened if i closed browser before submitting doh!

...so far netgear seems solid...

I've had good experiences with netgear stuff too.

While I haven't used a WIDE range of stuff, the products I've used have always perfomed as I'd expect them to, with no issues.

That's all I really ask for in hardware, and for the price I'd recommend them.

This is usually the part where 5000 people chime in with "XYZ is so much better", and while they may be, until I find a product doesn't do something I need, it doesn't need changing.

alieware are sooo overpriced but its your money

my mate bought one of there P4 3.6 laptops over a year ago think weighs like 14kg comes with it own backpack cost him 4g had like a 7800gtx or something in it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...