Jump to content
SAU Community

Recommended Posts

Hi Guys,

My wing's brake lights seem to have died. I ripped them out to test various things, and the car's putting 12v up to the lights fine...

Anyway, I'm in the market for a replacement. It's a stock R33 GTS-T type-m wing. Anyone know who's the best person to see about these things? Or perhaps someone has a spare one lying around collecting dust?

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/
Share on other sites

I remember reading about this a longtime ago.

Apparently the lights are all LED's wired in series so they can take the 12v.

The bad thing is if one stuffs up the whole lot won't light up (cause they are wired in series).

Pull the light out of the spoiler and check each LED, when you find which one is stoofed just replace it.

The hard part will be finding a replacement LED the same brightness as the others. Might be easier to replace them all so they all look the same.

J

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-178715
Share on other sites

I assume you mean the series 1 spoiler, the curved one that sort of rounds off the back end?

Yes it is a pain to get the lights out of it, the best way is a ratchet with a screwdriver bit, works a treat. Also, I believe the LEDs aren't strictly in series - they are grouped into lots of 5-10 LEDs, and all of the groups are wired in parallel, so that if you blow an LED, only the group that it's in is affected, not the whole array.

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-179677
Share on other sites

thats right with what Revhead said, they are in groups, i had a few out on mine when i first got it, it is an aftermarket GTR wing but the principal is the same, it had actually got water inside the casing of the light and corroded part of the circuit board away, re-soldered it back together and put some silicone around it all and it worked a treat, it was just a hassle to take out as the whole wing had to come off.

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-179765
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...