Jump to content
SAU Community

Recommended Posts

Heya all,

Same old problem. Drive around, then put it in neutral. Car drops to around 500rpm, then stalls.

I cleaned the AAC like nobody's business, and still no luck. I'm running an aftermarket BOV, but am

plumbing it back.

Visually inspected the AFM and it seems fine. Is there any way to tell if it is the cause of the problem?

If I can't fix it myself, I'll have to fork out big dollars to get everything inspected one step at a time.

I've heard rumours of an idle speed control solenoid, air regulator or throttle position sensor, but the details

on them were sketchy at best.

Please help me out,

Thanks,

Adrian.

Link to comment
https://www.sau.com.au/forums/topic/109749-yet-another-stalling-problem/
Share on other sites

Just found out that with the A/C on, it wont stall. So I'm writing it off to an rpm setting issue, and will turn up the revs on the old girl, see if that sorts it out.

Will post the results on here either way.

Thanks,

Adrian.

As an update, I cleaned the AAC, it's sparkling inside now. Put it all back

together without a drama, and it still stalls.

Other causes I've read about are as follows:

AFM dirty or oily

Fuel Pump earth wire

Fuel Filter clogged

Throttle Position Sensor needs adjusting

Crank Angle Sensor needs adjusting

I'm going to attack my AFM with carby cleaner tonight and see if that makes any difference. If it STILL stalls, I'll look into disconnecting the AAC plug, and check if that stabilized idle. If it does, I might not bother re-connecting it.

I'm also planning on changing fuel filter, and fitting iridium spark plugs.

Will eventually find the gremlin, then I'll let you all know :O

As an update, I cleaned the AAC, it's sparkling inside now. Put it all back

together without a drama, and it still stalls.

Other causes I've read about are as follows:

AFM dirty or oily

Fuel Pump earth wire

Fuel Filter clogged

Throttle Position Sensor needs adjusting

Crank Angle Sensor needs adjusting

I'm going to attack my AFM with carby cleaner tonight and see if that makes any difference. If it STILL stalls, I'll look into disconnecting the AAC plug, and check if that stabilized idle. If it does, I might not bother re-connecting it.

I'm also planning on changing fuel filter, and fitting iridium spark plugs.

Will eventually find the gremlin, then I'll let you all know :thumbsup:

Did you adjust the idle speed using the screw in the base of the AAC (driver's side)?

Clogged fuel filter usually has the opposite effect - idles fine, won't accelerate.

Just took my car for a spin and had a thought:

I noticed that when the boost gauge reads -0.6 on idle, the revs are around 650-700rpm. However, after driving then clutching in, the boost gauge drops to around -0.8, then slowly comes back up to -0.6.

My question is - is this cause or effect?

Is the low boost gauge reading causing rpm fluctuation, or is rpm fluctuation causing varying boost level readings? Or are both of these effects of the same cause?

Thanks pal. I took the AAC off the car and cleaned the sh*t out of it

with carby cleaner, got it looking real schmick. Then I put it back on and

hey presto - no difference... :D

I heard that disconnecting it can correct the problem, but then it runs a

certain rpm idle no matter if A/C is on or off. I would rather fix the

problem properly, if I can.

Thanks a bunch for your help.

Okie dokie

I didn't mean take the AAC off (as that would obviously leave a giant gaping hole out the side of my inlet manifold).

What I meant was disconnecting the plug that goes to the AAC.

Edited by Johnny Cash

ok, here is procedure to check your AAC valve properly. you'll need a multimeter.

my guess is either voltage between pin 1 and ground will be wrong, or the resistance between pin 1 and pin 2 are wrong, if everything is fine start looking at other things.

(sorry about the large images...)

aac1.jpg

aac2.jpg

aac3.jpg

aac4.jpg

aac5.jpg

aac6.jpg

hope this helps :D

Well it certainly looks like a lot of words and fancy pictures. Pity I know nothing about this sort of stuff. If I can't fix it with a screwdriver and a hammer, then it's beyond me.

Multimeter? I wish!

i dunno if this will help but, since uve mentioned that ur running with an aftermarket bov, have u tried putting a different bov? or installing ur stock one back? coz some ppl had this problem and usually the bov had been leaking or something like that, hope to be in help

Nah it all works a treat now. I just cleaned the AAC and AFM.

I used carby cleaner for the AAC, and electrical contact cleaner for the AFM.

Purrs like a kitten, thank god. Let's just hope it stays that way.

Thanks for all your help, guys.

She almost stalled on me this morning, but she was cold, and I was running my BOV atmo, so they could be causing it. I'll tighten the sh*t out of the BOV when I go home for lunch, and see if that makes a difference.

If it only happens when its cold, I'll let it go. It's when it's warm that it concerns me. It's hard to get going in the morning, like its owner :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...