Jump to content
SAU Community

Power Fc Wont Start The Car

teazn_r33

By teazn_r33,
in Engines & Forced Induction

 Share

Recommended Posts

teazn_r33 Mentor

teazn_r33

Posted
Posted

pplz i brought a power fc off a memeber on here just finished rebuilding my motor went to start it today and the power fc wont start the car when i turn it on and the fuel pump wont stop running and all the lights on the dash flicker

so i grabbed a standard ecu and it starts can somone out there help me asap as im in need of this car so i can go away

Link to comment
https://www.sau.com.au/forums/topic/110114-power-fc-wont-start-the-car/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

yes series 1 and series rb25 use the same model powerfc.

the only suggestion i can offer is to

check the powerfc is connected properly (loom plug is in OK)

no bare wires on the loom are shorted out

no wires loose or not connected properly

the powerfc doesnt have a burnt smell to it

does the hand controller come up and run ok if you just turn to ON and don't start the car? like can u actually use the hand controller like this?

teazn_r33 Mentor

teazn_r33

Posted
  • Author
Posted

umm no boost kit that i know about but how do i turn it off also no burnt smell the screen flashes with the sound of the clicking of the car its lights up i might try the power fc on a mates car

how do i turn the boost kit off i dont think i have one ???

Craved Grand Master

Craved

Posted
Posted

try it witha jumper battery connected, noticed mine turns off and will not start the car without heaps of power..

plus it always turns on the dash lights then switches them off, clicks then they come on and car starts..

teazn_r33 Mentor

teazn_r33

Posted
  • Author
Posted

i cant get into the menu the screen flashes on the hand controller the relay in the back on the car in the boot next to all the fuses clicks as well while trying to start

i pmd the guy who sold it to me no reply yet

it was brand new im just hoping i can fix it the car has being off the road for 5 months now icthing to get it going

if i put up the numbers of the ecu can someone tell me wat model it is for ??????????

paulr33 Grand Master

paulr33

Posted
Posted

on the side of the ecu it should have the the model number

your looking for ECR33 or RB25 something something which should confirm the model number. its on a white sticker

when mine was fried the screen would go crazy and make constant ticking noises and never boot up

teazn_r33 Mentor

teazn_r33

Posted
  • Author
Posted

well the way i figue it can be the relay cause the stock ecu starts it no props im goin to try the power fc on my mates car today and ill post some numbers up if i cant get any futher with it

johnny cash : slept like a log just finshed work at doms

The Mafia Grand Master

The Mafia

Posted
Posted

hey, mine did the exact same thing when we had the AFM wired up wrong. All the dash lights flicker on and off, the fuel pump goes flat out, and then eventually the fuse blows and the dash stops flickering.

Scared the shit out of us. No damage to the powerfc, just a blown fuse.

If its not the AFM, it will be something else shorting the f**ker out.

Good luck mate, and be careful.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...