Jump to content
SAU Community

Nissan RB20 / 25 parts

Spoolup
 Share

Recommended Posts

Sydneykid Grand Master

Sydneykid

Posted
Posted

Hey Brad aren't you going to a wrecking yard for them to send one to me next week? Yeh that's me!

Tell me about the RB26 stuff? PM or email is OK.

Roy Grand Master

Roy

Posted
Posted

Are we sure that the factory cast exhaust manifold is identical between the RB20 and the RB25. If you can assure me its identical, as in i want to use my OE R32 RB20DET heat shield on it, then ill take it for $80 + COD.

If that nots the case, are you able to get me an original RB20DET exhasut manifold for the same price.

Spoolup Mentor

Spoolup

Posted
  • Author
Posted

Trust Stainless Ex manifold suit RB20 / RB25 $800 - $750

TD06 19C, suit reco (worn thrust bearing) $550 as is - $500

ECU, Air flow meter, Loom to suit RB25DET $300

RB25DET Std injectors $200

RB20 / RB25 Std ex manifold $80

RB25DET Throttle Body $75

RB30 Series II block, crank, rods etc $80 - Sold

email. [email protected]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      It's been quite the ordeal but hey, at least you figured it out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...