Jump to content
SAU Community

Recommended Posts

Hi All, I need to make a resistor pack for my RB20DET to fit in my GTR injectors and I am unable to find instructions... I am guessing they would be somewhere or that someone has done it so I would love it if someone would take to time to point me in the right direction.

I don't have a stock GTR resistor pack and need to get them in tonight / tomorrow otherwise Ican't get my car tuned with them this weekend :)

Thanks in advance!!

Dunno about making one, have you tried searching for it?

You could call an import wrecker to find a GTR one.. I also remember reading somewhere that you can use the resistor pack out of an R30..

doing a search would be your best bet on finding the instructions tho, if there are any..

Thanks mate, I can't find anythng concrete so I though someone may have done it...

I really need to have it and installed by Friday befor Dr Drift comes down (to Tassie) so I figure making one may be quicker than finding one and getting it here! (And a lot cheaper).

There's a wiring up guide done by ROY in the tutorial section, I dropped in new injector plugs/boots (To suit VL, VL inj. plugs are the same as GTR inj. plugs, 6 inj plugs/boots cost me ~$53) while I was there as it was a real pain in the arse to trim up all the injectors so the plugs were suitable.

With regards to making a resistor pack. Buying the high quality resistors that it requires will cost you all up around $100. You are better off simply buying a second hand gtr resistor pack for the same/similiar price.

OR... Do what I did and used an Aussy R30 Skyline resistor pack, R30's are everywhere at the old car wreckers. I've seen them go anywhere from $5 right up to a whopping ~$15. :happy:

  • 1 month later...

sorry to bring up an old thread...

but so its confirmed 100% that gtr injectors can be run with a r30 resistor pack - using stock ecu / power fc ...

also where is it exactly located in the r30 and what does it look like (exactly)

and what does an r30 look like hehe - what year?

thanks :(

-Matt

Edited by huddy

The R30 uses the usual automotive plug 8pin plug that is made by various manufactures such as navara etc. They can be picked up from the local auto store for around $3.95.

Have a look in the tutorials section for a guide + pics written by Roy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...