Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

stan id b up for a set the bolt directly to the car n not the plastic kick panel and scratches easily. metal is really easy to polish up so i felt this way would b a little better. but thats just my opinion

HI2U: We're looking at 1-2 weeks for the prototype (R34GTT 2 door) then that one is ready to roll out.

For all other models, it all depends on how soon I get confirmation of sizes and how soon I get stuff measured up and drawn. R34GTT panel took 8 hours to draw up, pleae be a little patient.

Primordial: Thanks!

Tangles: Thanks to you too!

KamikazeR33: We could offer you a direct replacement item... it will consist of a brand new kickplate + our panels installed and sent out to you. Of course, this new plate will be from Nissan which will up the cost etc. etc.

Reason why we've gone for the "plate only option" is so members are not going to have to pay heaps to dress up their stock plates. If you are concerned about your existing plates or the installation, we can do both for you (at a premium)

Overall, these units were designed with the client in mind... most people will appreciate that this is going to be kept at the lowest cost possible, but still generate the highest effect!

However, I do appreciate ALL feedback on the designs good and bad... so keep em coming!

:P I'll definitely buy a pair for my 33 if you develop them, my kickplates are all scuffed & dirty.

In my wildest of dreams I'd get some custom made metal kickplates with the "skyline" embossing lighting up when you open the door, like in some mercs. A man can dream :laugh:

Your dream could become a reality but seriously it's not really worth your time and money.

The way to do it would be to get the SKYLINE bit cut out instead of etched, then applying a clear polycarbonate film on the surface. Underneath this panel you'd put in lights of whatever colour, shape or form.

Just thinking about it is making me twitch... the cost would be too great to justify a once-off custom fabrication :P

yep, as I said "in my wildest of dreams"

I could never justify the time & money spent on such a project.

Are you still considering a carbon fibre version? I read some mention of it in thread before this one.

Carbon Fibre version still an option yes...

Anthony, when do you need the 32 plates by? Let me know and I'll get that happening ASAP - still need some plates to measure up dammit!

hey stan, sorry if i confused u i just re read my post n wondered if i really did post that

i meant not to use the plastic panel at all but use a full metal kickplate instead with the design on it? this option may be useful as im going to assume if its just goin to be a rectangular plate it could b a multifit item

Can anyone confirm that the GTR kickplates are identical to the GTST kickplates across all three models?

If this is the case it will save me a lot of time :O

Pretty please somebody?

R34's are. I can tell you that much

Thanks guys...

Kamikazee: The cost involved will not be worth my time or the clients'. Also, having a metal kickplate will not be good as metal does dent - purely keeping it to the small replacement plates will mean that it's more manageable.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...