Jump to content
SAU Community

Recommended Posts

  vst20 said:
hey ppl

I have a rb20 in a vs commodore just wonding a u thing of it

there are alot of ppl dong turbo conversions to the commo's now. i suppose its a different idea, but if it were me, id most likely just put my $ towards a turbo car, instead of puting all the money into a conversion like that. but each to there own.

  85URK said:
there are alot of ppl dong turbo conversions to the commo's now. i suppose its a different idea, but if it were me, id most likely just put my $ towards a turbo car, instead of puting all the money into a conversion like that. but each to there own.

Yer i know but i wanted something different

Hmmm, I would have thought that having such a low capacity engine would be a bad idea in anything other than an early model Commdore due to the lack of torque. RB25 would be a better solution, but personally I would have gone the 1JZ or 2JZ. 1JZ halfcuts are still pretty cheap too I believe.

Good on you for being different though.

Edited by Thunderbolt

The ecotec V6 in the VS model produced 147kw at the fly

The Silver top Rb20det is 164kw at the fly....

However the torque would be better in the V6 as it had a storter stroke and larger bore....

Either way you can buy a million parts to make an rb20 better but you cannot just pick up a catalogue for a buick V6....

Nice job.... I have wired a VB with an rb26 and a Vk with an rb25 in the past few years and it was not easy at all... But plenty on fun...

i know a guy who has twin turboed his VN V6 executive motor, has GTR turbo's on it running a wolf computer. but he's lost his licence for like 2 years so its been of the road. also there is another guy getting round up here with a 1jz conversion in a vn commo, goes fairly well.

mate jus swapped his riced out lancer for a twin turboed vr commo ute.runs 300zx turbos and haltech and alledged internals.

supposed to have 340hp at the treads but runs like a dog atm. with a tune and a bit of sorting it may be alright. would have thought the 300zx turbos (t25??) would have been a bit small for a 3.8L. it makes 10psi at like 2000rpm.

that would be a weapon of a bimmer overev1

Edited by rb20inside
  rb20inside said:
mate jus swapped his riced out lancer for a twin turboed vr commo ute.runs 300zx turbos and haltech and alledged internals.

supposed to have 340hp at the treads but runs like a dog atm. with a tune and a bit of sorting it may be alright. would have thought the 300zx turbos (t25??) would have been a bit small for a 3.8L. it makes 10psi at like 2000rpm.

that would be a weapon of a bimmer overev1

well gtr turbo's are only T28's, like the ones on my mates, its alot of stuffing round in the end, i told my mate with the amount of money hes spent on his vn he coulda had a 12 sec car easy, and done a RB26 conversion to it, he's kicking him self about it now, but thats what u get for trying to flog a dead horse i guess.

Edited by 85URK

There are buick V6s that came stock turbo... Not here but in the states. They run some insane times considering the lard arse cars they are in. I really dont understand why more people dont do them over here. Commos make awesome sleepers tho.

A VN-VS commo weighs about the same as a cefiro or skyline sedan anyway, I dont see the problem.

Out of interest tho, whats the fuel economy like now? Better or worse.

  dangerous_daveo said:
There are buick V6s that came stock turbo... Not here but in the states. They run some insane times considering the lard arse cars they are in. I really dont understand why more people dont do them over here. Commos make awesome sleepers tho.

A VN-VS commo weighs about the same as a cefiro or skyline sedan anyway, I dont see the problem.

Out of interest tho, whats the fuel economy like now? Better or worse.

Not to sure yet mate i do not have a licence to drive it but i might lend it to a mate and i will let u know what it is like on fuel

And thanks for the feed back

cheers

  • 2 weeks later...
  vst20 said:
the vs is off the road again f**ked a gear box :laugh:

Is this car regoed? or mod plated? i thought you couldnt do a engine swap if the motor is older than the car????

Edited by shnaped_second
  shnaped_second said:
Is this car regoed? or mod plated? i thought you couldnt do a engine swap if the motor is older than the car????

You can swap just about anything within reason...

I have seen an rb26dett in a VY Commodore... So thats in the same boat....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...