Jump to content
SAU Community

Recommended Posts

hey guys, i was just wondering what the easiest way is to identify an L.S.D on an R34 GT-t, without just baggin em up, as its not my car. i'm pretty sure its an LSD, as wen ma mate plants it, the back comes around very quick, when he launches, it even steps out a bit, but another mate of mine keeps tellin me that its not, coz he cant find a tag on the diff itself (and hes a mechanic that deals with quite a few skylines, so i cant just tell him hes plain rong, i want some evidence). is there anythin in the VIN number that will tell u if its an LSD or not? like on the supras? is there something i need to look at on the diff itself?

cheers,

Ben

Edited by VB-
Link to comment
https://www.sau.com.au/forums/topic/110869-lsd-identification/
Share on other sites

Guest Mashrock
hey guys, i was just wondering what the easiest way is to identify an L.S.D on an R34 GT-t, without just baggin em up, as its not my car. i'm pretty sure its an LSD, as wen ma mate plants it, the back comes around very quick, when he launches, it even steps out a bit, but another mate of mine keeps tellin me that its not, coz he cant find a tag on the diff itself (and hes a mechanic that deals with quite a few skylines, so i cant just tell him hes plain rong, i want some evidence). is there anythin in the VIN number that will tell u if its an LSD or not? like on the supras? is there something i need to look at on the diff itself?

cheers,

Ben

jack the rear.

turn wheel by hand.

both go same way lsd.

different ways not lsd..

yeh i thought about that, got anything easier? i really cbf with that, u see, im kinda the lazy type, and i dont like workin with those bodgy wind up jacks personally. ma mate would probly freak and not let me jack it up anyway... he doesnt know all that much wen it comes to cars, and panics wen anyone touches something, if he doesnt know wot it is himself... basically everything. thanks for the tip, and keep the ideas comin

cheers,

Ben

your mate should be able to tell, just from the feel of it when launching / kicking the tail out a bit. When you kick it out, it should stay out if you get my drift (pun intended), if it just goes straight, or you notice one wheel spinning on the spot, then it's not an lsd.

Or going up driveways slowly, or driving on a dirt road that's bumpy, you should be able to notice it single-spinning if it's an open diff.

Also, i thought all turbo skylines had a factory lsd?

I think if you jack up one side, with car in neutral, should be hard to turn the wheel that's off the ground. (be careful because if it's an lsd it'll try to turn the wheel that's on the ground, just make sure wheels are chocked and car doesn't try and roll off the jack....)

c'mon man, it'll take 5 mins! that's pretty lazy...

hitting friend with spanner sounds like a good idea. all GTT's come with factory LSD.

sometimes HICAS on GTTs can make it seem that it has an LSD because how easily the back kicks out.

try full lock to the right when pointing up a hill and just plant it, 1 wheel burn out = no lsd, 2 wheel burnout = more fun... plus LSD.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...