Jump to content
SAU Community

Recommended Posts

I have them in my car and the improved handling is noticable, yet I meet other members and they haven't heard of them, its a bit hard trying to describe them because I really dont know what they do, although I know the difference of before/after.

BEFORE

When entering a corner I could feel the body move/angle over to the opposite of travel and then the shocks/springs dampen this effect.

AFTER

No body movement just springs/shocks doing their thing, still has body roll (until whiteliners are in)

So I assume that the pineapples fill or harden a soft (family car) spot in the setup, can somebody fill in the gaps for me? :wub:

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/
Share on other sites

Did you put the 4 in or the 8 in. Are yours poly or aluminum?

I have 8x 4-5mm thick aluminium ones in, and I want to pull 4 out to see what it does. I dont think the 8 are really helping, just contributing to in cabin noise from the diff.

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2054983
Share on other sites

sell em here for $99 per set, Bee R brand

http://www.otomoto.com.au/beer.htm

from the website:

Adding these bushes to the rear suspension cradle in any RWD Nissan (and GT-Rs) from 1988 to 2002 reduces cradle movement dramatically to give a more consistent, predictable feel to the rear end, which is especially valuable for drifting. By altering the static angle of the cradle, pineapple bushes also promote rear suspension squat for greater rear grip.

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2055222
Share on other sites

I wonder if someone can answer a related question for me on this.

There are 3 setups you can use pineapples for, Drift, All round, Drag

I think sydneykid posted a "where to install them" for each setup, but my question is...

The pineapples i bought came with 4 small rings and 4 large rings, if i'm setting it up for drift, do i use 2 small ones and 2 big ones and just not use the other 4? or do I use all 8??

And to anyone who uses them for "drift", how much does it effect oversteer? I'm wondering if i should just use the 'all round' setup for them, becuase i'm not having any major understeer problems, and i dont want to make the car too spin-happy!

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2057706
Share on other sites

I wonder if someone can answer a related question for me on this.

There are 3 setups you can use pineapples for, Drift, All round, Drag

I think sydneykid posted a "where to install them" for each setup, but my question is...

The pineapples i bought came with 4 small rings and 4 large rings, if i'm setting it up for drift, do i use 2 small ones and 2 big ones and just not use the other 4? or do I use all 8??

And to anyone who uses them for "drift", how much does it effect oversteer? I'm wondering if i should just use the 'all round' setup for them, becuase i'm not having any major understeer problems, and i dont want to make the car too spin-happy!

Apparently the setup for drift makes it stupidly slippery. Best to set it up for allround if you just want the subframe firm, or put them in with the Noltec subframe bush kit to set the subframe for traction.

4 small ones for traction according to whiteline.

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058009
Share on other sites

I dont remember what was put in mine but they are Purple and on the bottom of the subframe so its all round performance, nolathane bushes went in as well.

So I can say to the peoples that they reduce the cradle movement and give a more presice feel to the rear end.

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058256
Share on other sites

Be carefull, the article in HPI/ZOOM is missleading.

The Otomoto kit only has 4 bushes. 2 large (not split) and 2 small (split). When you use the 2 small bushes below the subframe you have to tie wire them otherwise they WILL fall out.

As you can see from the instructions (copy following) the Whiteline kit has 6 bushes, 2 large (not split), 2 small (split) and 2 small (not split). The 2 large bushes do not need to be split as they are mounted below the subframe. The 2 small split bushes are for fitting above the subframe without removing the subframe from the chassis. The 2 small non split bushes do not need to be split as they are mounted below the subframe. Since they are not split, they WILL NOT fall out, ie; they do not need lock wiring

Whitleine_rear_subframe_instructions.jpg

For $5 extra I would buy the Whiteline kit, get the extra 2 bushes and avoid the need for lock wiring, which is not a permanent solution.

:P cheers :O

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058355
Share on other sites

Did you put the 4 in or the 8 in. Are yours poly or aluminum?

I have 8x 4-5mm thick aluminium ones in, and I want to pull 4 out to see what it does. I dont think the 8 are really helping, just contributing to in cabin noise from the diff.

I have 8 aluminium ones in (c type), and to tell you the truth - the noise does not bother me at all. You certainly notice it's there, but what's a little bit of noise on a sports car. If you don't like noise then you should get the polyurethane ones.

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058461
Share on other sites

no offence Syd kid i have the otomotto kit and i have 2 large split and 2 small non split

Interesting, the sample kit I have has 2 large split and 2 small split

If the 2 small are not split, how did you get them above the subframe?

Remove the subframe?

Or cut the bushes?

:P cheers D

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058460
Share on other sites

ok, thanks for the replies, but i'm even confused now...

the kit I have (alloy pineapples) has 4 large split, and 4 small not-split... (the smaller ones are the thicker ones yeah?)

so go figure!!!

I might give them a try in "drift" mode and if it's too spin happy i'll change them to "all round"

also, which way around do they go?

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058466
Share on other sites

http://www.driftshop.com.au/suspension_files/subframe.JPG

^ these are the ones I have....

is install different from the whiteline ones? I need to know the correct layout for "Drift" and "all round"........

Edited by MerlinTheHapyPig
Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058476
Share on other sites

The whiteline ones are urethane, and are there to change alignment of the subframe.

The alloy ones u got there are designed to crush up the std bushes to stop flex in the subframe, without changing alignment of the subframe.

In your case i think the c ones go in the top, and the others go underneath, so its meant to fit without removing the subframe.

Link to comment
https://www.sau.com.au/forums/topic/111428-pineapples/#findComment-2058495
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Perfect, I'll get to it this winter then at the same time as I weld on my anti squat kit. 
    • Alright so my 32 only has one temperature no matter what degree you set it to. I’ve tried disconnecting the servo motor arm and moving it either direction and got no change. I’ve fixed the leak in my AC and re charged it and with it on and clutch engaged it still blows hot even though the low pressure pipe going to the firewall is ice cold. Both heater core hoses are hot while running as well. Diagnostic code showed 24 for intake air temperature sensor. Anybody got any ideas?
    • I said Garrett style. Not Garrett genuine. And something in the G30 550 range is what you want. Not those pokey little old fashioned T28 sized things. The intake ports in the head are small. There is little benefit in fattening up the runners and leaving ths actual ports small. Just run what you've got. And on the subject of Nistune vs Haltech etc..... You know you can control the transmission with decent standalone ECUs these days, right? No need to keep any of that old Nissan bullshit. Don't get me wrong - I use Nistune on my Neo. But it is a DET, so the number of bodges and workarounds I had to do to make it work in a chassis without ABS, TCS, etc, is quite small compared to the herniated arsehole you will have trying to make it work on a motor that doesn't have some of the things that the turbo ECU wants to see. Just easier to bite the bullet and go aftermarket outright.      
    • Hmm. Only when the f**king thing is actually working. Still can't find the leak. And that's with dye being put in the last 3 times!
×
×
  • Create New...