Jump to content
SAU Community

Recommended Posts

I am replaceing my standard rotors with slotted ones.

Have removed the calipers and pads but cannot remove rotors.

Am I forgetting something?

I used a bit of WD-40 to loosen them, thinking they are just stubborn. Am going to try again tonight but want to be sure I am not missing removing something. I even tried a bolt into the two holes to get it pull away from the hub but that didn't help didn't feel good got very tight but did not loosen rotor.

Advice needed...

Link to comment
https://www.sau.com.au/forums/topic/111525-trouble-removing-rotors/
Share on other sites

I am replaceing my standard rotors with slotted ones.

Have removed the calipers and pads but cannot remove rotors.

Am I forgetting something?

I used a bit of WD-40 to loosen them, thinking they are just stubborn. Am going to try again tonight but want to be sure I am not missing removing something. I even tried a bolt into the two holes to get it pull away from the hub but that didn't help didn't feel good got very tight but did not loosen rotor.

Advice needed...

What car? R32? If so just use the threaded holes to slowly work the rotor off. Might help to tap the rotor (near stud holes) with a mallet to help work them off. Just do it slowly, and be patient. They will come eventually, norlmally have not been off for a long time.

What car? R32? If so just use the threaded holes to slowly work the rotor off. Might help to tap the rotor (near stud holes) with a mallet to help work them off. Just do it slowly, and be patient. They will come eventually, norlmally have not been off for a long time.

Its an R33 GTST S2, I have used holes to work bolts into they got very tight was waiting for thread to rip out, tried mallet and WD-40 still no joy....

Its an R33 GTST S2, I have used holes to work bolts into they got very tight was waiting for thread to rip out, tried mallet and WD-40 still no joy....

Mine were very tight too. just keep pressure on the bolts screwing the rotor out, tap away with the mallet. Pressure and shock impacts should get them off. Just dont be too savage. At the end of the day you said you were replacing them anyway.

i did this exact same thing 8 months ago on my r33 s2 gts-t.

Basically the easiest way i found after swearing for agood 2 hours why the basterds wouldnt come off was the following

Put the screws into the holes, instead of pulling like i did just keep screwing them in till they get really firm as they will act as leverage to push the rotor away from the back. Get a rubber mallet and give it a whack (not to hard obviously) working around the corners. It should pop off if it doesnt keep trying to turn the bolts as they are the key when they have managed to loosen the rotor off a little bit they will come off easy as :teehee:

Cheers Leigh

  • 7 months later...

hey ppls

im having the same issues with the rear discs.. the barstard wont come off..

ive taken the calipers off.. and besides that i havnt undone any other bolts if im supposed to ?? ive been hitting it / the 5 bolts for an hour.. nothing seems to be happening.. any good ideas :( ??

also theres 2 little holes on the discs.. theres like a metal screw thing inside them but u cant do anything to it.

???

hey ppls

im having the same issues with the rear discs.. the barstard wont come off..

ive taken the calipers off.. and besides that i havnt undone any other bolts if im supposed to ?? ive been hitting it / the 5 bolts for an hour.. nothing seems to be happening.. any good ideas :( ??

also theres 2 little holes on the discs.. theres like a metal screw thing inside them but u cant do anything to it.

???

Is the handbrake up or down? if its off just belt them inbetween the studs, they will loosen up, dont use a rubber hammer its a waste of time

do u get them out from behind or something ???

cause i cant see them sticking out or anything...

Some discs have screws some dont, if they have em they will sit flush with the rotor inbetween wheel studs, if they havent been off in a while you'll need a good hammer, WD40 will help too, and lets not forget perserverance! :(

are u talking about the 2 screws ive circled in my pic ??

how do i get them out.... ?? theres nothing to put the spanner on..... ??? or am i missing something :( ?

this hammer you speak of.. wat am i hitting specificaly.. i was hitting the rotor before, but that didnt do squat

thanks :ninja:

post-19018-1163238517.jpg

hey dude first off as it has been mentioned is you hand brake off? If its not then it will be near impossible to take the disc off.

Second there is no screws holding the discs on, the two holes u have circled are for YOU to thread 2 bolts into, do them up and the disc will pop off.

are u talking about the 2 screws ive circled in my pic ??

how do i get them out.... ?? theres nothing to put the spanner on..... ??? or am i missing something :( ?

this hammer you speak of.. wat am i hitting specificaly.. i was hitting the rotor before, but that didnt do squat

thanks :ninja:

ok plan B.

Those little holes you circled, they are there to remove the disc if its tough,

They will be a 10mm or 12 mm bolt,

the bolt will have to be fairly long, and you just screw em in and they will push the disc off for you :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...