Jump to content
SAU Community

Trust turbo's

rob77

By rob77,
in Western Australia

 Share

Recommended Posts

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Rob, The garett turbo's are great, you just have to understand what effect they will have, and don't bolt one on randomly. HKS have slightly better trims but value for money the garett's win.

R33 Impul,

I have a friend who is custom making my manifold, but there are a number of people around town who can do it.

See'ya:burnout:

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

HKS don't give out the exact sizing or trim of there turbo's, therefore you would have to pull one apart to find out. I don't think comparing one turbo to another is very useful, just buy the one that will do the job. I am thinking of the GT3040, as it will be much cheaper than the HKS GT3037S.

See'ya:burnout:

macka Veteran

macka

Posted
Posted
Originally posted by rev210

The HKS turbo's are made by garret. If you can measure the HKS componets you can make your own 'identical' down to the HKS badge.

We know :P

But HKS design there own wheels and cores with Garrett housings so u cant make your own HKS turbo unless u could get an exact HKS replica wheel..

Anyway back on track......

Are trust turbos water cooled?

rs73 Grand Master

rs73

Posted
Posted

There is no way you can make an HKS turbo out of Garrett parts.

Garrett supplies the parts for HKS which are different to Garrett retail parts itself. There's an agreement between Garrett & HKS that Garret will never provide those HKS-specific parts to others except HKS alone.

Lots of ppl tried and they failed to get the same power out of retail Garrett parts. HPI magz also confirmed this can't be done. Get a genuine HKS one is the only solution. This is the way HKS protects their business.

Steve Grand Master

Steve

Posted
Posted

Guys, if you are chasing a HKS turbo, I picked up a brand new GT3037S56T from http://www.fvej.com/perform.htm and it cost me $2700 delivered to my door.

Absolutely brand new - still had all the tape/plastic intact.

As you can imagine, I am pretty stoked, thought I'd put the word out as they told me they are pretty keen to get into the australian parts market.

Steve Grand Master

Steve

Posted
Posted

Yeah I am pretty wrapped - I was going to get one of Grant's, but he got back logged with the e-mails and this one came up before he replied - about $100 more expensive - couldn't resist as the new price on the GCG website is $5880.

Will let you guys know what its like when its in, but it will be a couple of months yet still got plenum, manifold, injectors, headwork, etc to go first.

Steve

Steve Grand Master

Steve

Posted
Posted

GTS-t VSPEC,

I am pretty sure that they dont come up too often at that price. I asked what was available and first off all he had was a few (about 4 or 5) different TD06s. Then this one came up so I grabbed it. Might be worth dropping him a line, let him know what you are after and asking him to keep an eye out.

I'm not even 100% that this will be big enough now - seriously thinking an RB30 conversion will be the go - it might be just a little on the small side? Just seems a shame to get it so cheap and then not even give it a spin.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...