Jump to content
SAU Community

Recommended Posts

Prior to this R33 GTS-T (auto) I used to drive a VS commodore which was about 100 KG heavier... now when going down the hill the VS just rolled like crazy picking up speed. The R33 which is lighter, doesnt roll well at all...Infact the only time it rolled good was when I chucked it into NEUTRAL (i heard its bad for tranny though).

Is this OK or? Cos i feel i could be saving petrol money if it rolled better.

The car is stock with stock wheels.

Also can anyone explain to me whats the go with over drive? I got cruise control and when i turned it off while cruising on 100 KM/h the revs jumped from 2.5 K to over 3.5 K and it slowed the car down so i turned over drive on.

Cheers

Edited by Sir-D
Link to comment
https://www.sau.com.au/forums/topic/112115-rolling-down-the-hill-in-r33/
Share on other sites

overdrive is a "4th gear"

so u drive around looking for hills to "roll" down to save money on fuel? Sorry im just trying to understand exactly what your getting at here thats all.

Rolling will mean u will sit on the brake more and wearing your brake pads quicker?!

overdrive is a "4th gear"

so u drive around looking for hills to "roll" down to save money on fuel? Sorry im just trying to understand exactly what your getting at here thats all.

Rolling will mean u will sit on the brake more and wearing your brake pads quicker?!

So i should always have over drive on ye?

no i dont look for hills :( its just whenever im rollinw down to the traffic lights that are about to turn red i still have to gas it a bit otherwise i lose all my tempo, the commodore had over 270000 KMs though, this one has 44000. Just trying to work out how i could make it roll bit better.

So i should always have over drive on ye?

Yes. It saves the most fuel and for power its okay because the car will know when you want to fang it and switch off overdrive itself.

I have only turned it off for dyno runs.

It rolls worse? Its actually ilegal to have your car in neutral while moving as its classed as not being in control of your vehicle.

As others have stated overdrive is 4th gear. Its the same as rolling down a hill in first in a manual unless you put your foot on the pedal you will only roll at a certain speed.

It may be related to the TPS - Skylines in general cut fuel to the injectors when the throttle closes and the engine is above about 1200 rpm. The Commodore might not do this.

I know my R30 only does the fuel cut above 3200 rpm, so it rarely cuts fuel on throttle backoff. As a result, it tends to drive down hills. My R32 does do fuel cut, so it basically maintains speed down hills. It's almost like an engine brake.

Having both auto Skyline and VS dunnydore, so I know what he's talking about.

The VS auto, especially around town, doesn't lock up at moderate speeds, so when you roll downhill, you notice the tacho drop down to a fast idle. (Really great for getting booked by the coppers hiding at the bottom of the hills.)

The Skyline locks up at a much lower speed, It's quite noticeable when you swap from one car to the other. Makes you think you're still in 3rd, but at least you don't have to roll downhill with the bloody brakes on.

Having both auto Skyline and VS dunnydore, so I know what he's talking about.

The VS auto, especially around town, doesn't lock up at moderate speeds, so when you roll downhill, you notice the tacho drop down to a fast idle. (Really great for getting booked by the coppers hiding at the bottom of the hills.)

The Skyline locks up at a much lower speed, It's quite noticeable when you swap from one car to the other. Makes you think you're still in 3rd, but at least you don't have to roll downhill with the bloody brakes on.

Thanks dude. Commodores arent that bad though :laugh:

  • 3 weeks later...

I think it's mostly due to the gear ratios. The Skyline auto does around 3000 rpm in top gear at an indicated 110km/h, while the Commodore is doing around 1800 rpm in top gear at the same speed.

We've had a pile of Calais' over the years (company cars) and I swear, every gearbox has been programmed differently. There is a large hill near our place where you start out at about 90km/h and by the end in the Calais you will be doing around 115km/h, but in the Skyline you would probably only hit 100km/h if you're lucky. In the first Calais' the revs used to hold at whatever they would have been with the accelerator depressed in top gear, then a couple of cars after that used to drop revs to idle, then raise them back up, then drop, etc. Then another one would just drop them to about 1200rpm all the way down the hill. The one we have now (5 spd auto) seems to keep revs as if you are in top gear, like the first cars. Dunno why they keep on changing, but I suspect they're to do with how the transmission logic is programmed.

Oh yeah, I had a point to all that... the cars that kept the revs equal to top gear (locked torque converter?) seem to roll the best. The Skyline seems to drop revs slightly when you lift your foot off, so I suspect the torque converter becomes unlocked, so possibly that puts extra drag on the engine, and combined with lower gearing (more engine braking because of increased revs), that may account for the extra rolling resistance?

Also, just out of interest, the Calais has an instantaneous fuel consumption feature on the trip computer, and all cars except the ones that used to raise and drop the revs intermittently read 0.0L/100km all the way down the hill. Dunno if that's actually true or not, but it sure would be nice! :(

Also, I just keep overdrive turned on all the time. That's certainly the way to go if you're trying to save fuel. I find the car's fine at all speeds like that - the transmission seems a lot more responsive than any of the Calais' we've had, even the newest one with the 5 spd auto!

oh... oh dear... over drive !! lol, do the 1994 r33 gts's come with an over drive? Cause for that Newcastle Cruise I was sitting on 3k+ the whole way and back haha, how do I turn it on/off??

theres a button O/D on ur auto shifter...

when its on it should not glow on ur dash board... when its off it will glow OD or overdive.

post-23785-1146094274.jpg

oh... oh dear... over drive !! lol, do the 1994 r33 gts's come with an over drive? Cause for that Newcastle Cruise I was sitting on 3k+ the whole way and back haha, how do I turn it on/off??

I assume the gear ratios are the same for the S1 and S2 auto's, so I'd say you'd already have the overdrive on if you were doing around 3000 rpm at around 100 km/h. You'd be doing over 4000rpm if you had it off!

Damn I wish they had a 5th gear so you could cruise at 2000 rpm down the motorway - would be quieter, save fuel, less wear and tear... I know you'd have almost no torque at that speed but the auto's kick down pretty fast on light throttle so that probably wouldn't matter. Oh well, I can only dream... :devil:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...