Jump to content
SAU Community

Recommended Posts

I have owned the car for over 2 years and have been in the process of building it up almost the entire time. Most work was performed throughout last year and all the work completed by Gavin Wood, Autotech Labrador. Including full rebuild, 17,000km done including running in.

The work currently carried out to the car includes:-

(All parts bought NEW unless specified)

Genuine Nissan N1 Block ($3,500)

GTR Crank (replaced)

Adjustable Cam Gears

Apexi Power FC 'Plug N Play'

Apexi Electronic Boost Controller Kit

Apexi FC Commander Hand Controller

Apexi Super Intake kit for 80mm AFM's

Apexi GT Spec Intercooler (no longer in production) 136mm Thick

R33 Gtst 80mm AFM's <Used

Greddy/Trust Oil Catch Can

Greddy/Trust Intercooler Piping Kit

CP Forged Pistons

Tomei Metal Head Gasket

NISMO Fuel Pump

600cc injectors

HKS GT-SS Sports Turbines - Ball Bearing 320hp each

HKS Split Dump Pipes

HKS stage 2 cams and springs

Twin 3" Front Pipes into single 3.5" Exhaust. N1 Style Muffler

N1 Oil pump

N1 Water Pump

OS Giken Triple Plate Clutch R3C

Lightened Flywheel

Apline MP3 Headunit w/remote

Alarm System with Remote Central Locking

Bride Reclining Racing Seats w/genuine rails

Nismo Duracon Gearknob

TEIN Super Street Coilovers (adjusted for Australian Conditions)

(Height and Dampening Adjustable)

Front Strut Brace

Michelin Pilot Preceda Tyres 90%

Slotted Brake Rotors and Bendix Pads (new)

Price: $32,000 $29,000 Or Nearest Offer

Contact: 0413 244 862 - Jonathan

Location: Brisbane

IMG_0364.JPG

IMG_0120.JPG

250awkw @ 16 psi >> Capable of 360awkw @ 25 psi

IMG_0395.JPG

Edited by 600ZILLA
Link to comment
https://www.sau.com.au/forums/topic/112264-nissan-skyline-r32-gtr-1991/
Share on other sites

Thanks.

I will most likely pull this off the market shortly and continue modding. Its running absolutely fantastic day in day out. A rare example of a very low maintenance, high output vehicle with only a couple mods from being a real GODzilla.

HKS Ballbearing GT-SS Turbos and we are about to come into winter !!

An absolute pleasure to own and drive.

Stealth01 - I never recieved that PM.

Edited by 600ZILLA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...