Jump to content
SAU Community

R33 Thermostat


Recommended Posts

Guy's follow the bottom radiator hose up to where it joins the motor,,,thats the stat cover,,,3 bolts from memory.

The stat is the same as a VL 3.0L,,,Nissan Part No is 21200-42L05 and it fits all R33's.

Neil.

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-195749
Share on other sites

  • 6 years later...

ok guys, there are a few things to know here:

firstly for the money and time saving just get a genuine nissan one from nissan parts. they are around $50-60.

second, if you want a 'tridon' one...the part number is TT268-170. this is the 77deg one. there is an 85 deg one...dont get this!

lastly if you want to waste money, get the nismo one but these are over $100 if not closer to $150 and open at 67 or so deg.

you will also need gasket goo for this as there is not a norml gasket there. i use the blue stuff...works perfect!

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4606827
Share on other sites

bellow i attached instructions from the RB engine manual.

view order 3 then 1 then 2. (sorry i didnt rename)

as the above people have said use either the tridon or stnd nissan one.

tridon will set you back about $28 and its one of the good cheapies.

make sure the jiggle pin is pointing to the top of the motor.

for gasket sealent i recomend a product from loctight.

Its a silicone based gasket goo, its loctight blue something or other.

It's the ducks nuts, will come in handy down the track to.

let us know how you go.

post-55273-1242824646_thumb.jpg

post-55273-1242824666_thumb.jpg

post-55273-1242824704_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4606908
Share on other sites

was reading a thread recently and a workshop operator said he'd been through a bunch of tridon thermostats that were crap, and caused problems.

just use the nissan one. also there is no reason to use a lower temperature it will NOT help you, it just means your car won't get up to temp and you'll lose fuel efficiency.

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4608777
Share on other sites

  • 2 years later...

hi guys on my r33 gtst 1993 it has a braided cable that runs down threw the chassis and comes out next to the exhaust, and theres something that attaches to that which im not sure what it is or where to get another one because i scraped going over a speed hump and its pulled it out and stuffed it and i think its shorting out, my thermostat light is staying on and check engine also comes on itermitently. Any help on where i can get another one of these, and or what it is would be good cheers

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-6110663
Share on other sites

  • 2 years later...
hi guys on my r33 gtst 1993 it has a braided cable that runs down threw the chassis and comes out next to the exhaust, and theres something that attaches to that which im not sure what it is or where to get another one because i scraped going over a speed hump and its pulled it out and stuffed it and i think its shorting out, my thermostat light is staying on and check engine also comes on itermitently. Any help on where i can get another one of these, and or what it is would be good cheers

Disconnect it, it's useless. Pull out your passenger seat and delete that sensor

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-7274366
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...