Jump to content
SAU Community

Recommended Posts

what you could do with it. is mount it so the filter is facing the radiator. sure its not having air forced in to it. but its also not sucking hot air. the air hitting the back of the filter housing would act similar to an intercooler as it would get cooled by the air. or mb that just works in my head.

personally i would go for a pod in the engine bay with a good cold airbox and a cold air feed. removing the little rubber thing about the passangers side headlight helps get a little more air in there :D you can run a cold air feed with out cutting in to the body. just run it up behind the drivers headlight. i have had 2 PVC pipes running to it. and i have also had a bit of metal bent up with sides to direct the air up there.. both of those workd alright.

if u mount in front of radiator, dont expect radiator to work as well.

also dont forget that if rain needs to get in on a 45 deg angle to get in, that u dont need 45deg angled rain to do this - you only need you car to be moving forward at a decent speed

your largest raindrops have a terminal velocity of about 30-35km/h - so to get rain to come in at a 45deg angle, you only need to be driving at that speed.

your average light rain or drizzle is around the 15km/h mark, so again you only need to travel at that speed for the rain to be coming in at 45deg.

travel twice the speed its now coming in on a 60deg angle - and quickly you see how easily it will be for water to get in there if its facing an open airflow from front of car

if you look closely the front mount air cleaner has a perspex plate in front of it with holes in it and spaced out from air cleaner , i dont think water would be a problem , water injection anybody ? cooling possibly a problem ,depending how close mounted to radiator .

if u wore shoes with holes in them, would your socks get wet when it rains? no different here

they are purely for rice factor, it that isnt already bleedingly obvious. if your even considering them then you know the ricer inside of you is in control more than the logical minded skyline owner.

mate each to there own , i feel the ram pod style is the best from experience, just everybody was complaining about water problems,there is a deflector on it to reduce the problem ,a little bit of water cant hurt a motor ,but if you go through a creek .....

its no longer a ram pod if its got persplex in front of it. its got the worst of both worlds - no forced air assisstance, and it still gets wet if its mount where its visible (as you would, so u can show it off of course :P)

This airfilter may be ideal for bonnet scoop applications where the scoop sits center of the bonnet above the rocker cover just like a top mount intercooler.

but yeh still seems a bit rice for me, im simple... pod, sheild and ducting :P

Edited by adox

if your going to have ducting to your pod filter you can make sure its not aiming at your pod so if any water gets in there it dusnt go strait in your airfilter or you can block off the hole either in the engine bay or in the front of the bumper. when its raining the air is gennerally colder so you will still feel some benifits of the colder air.

easyest way for cold air.. remove the headlight :P even tho it dus look arse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...