Jump to content
SAU Community

Recommended Posts

I am currently running 13psi on mine. I will be getting a tune pretty soon so might bump it up to 14psi, but I'm not willing to push it higher than that. Personally I am pretty stoked at the performance I am getting at 13psi so I don't feel the need to go much higher.

I have killed 2 X R34GTT turbos at 12 psi.

They don't make any more over a genuine 12 psi anyway, they heat soak the air so much you get detonation. So you have to retard the ignition timing and loose all the power you gained.

:) cheers :)

more boost doesnt mean more power

more boost means more power (well airflow) only when you are still in the efficency zone for the compressor wheel. past 12psi as others have said and its off the efficeny zone, so you just dial in more and more heat and it goes bang

90% of all stock turbos will blow at a genuine 15 psi if run there often.

It's not boost alone that makes them blow. It's boost and heat which makes the exhuast wheel delaminate.

Do a seach and see. This topic has been covered a 'few' times before.

Hey there,

So for all you guys that have had the turbo die on you, was the turbo ever subjected to continuous high heat levels, i.e., drifting, track racing, or continuous on/off throttle runs through the gears in short periods of time?

The R34 turbo's must have a small efficiency range if they start to die around 12psi, just seems low to me, and a very quick drop off. You'd be able to verify this on a dyno by looking at inlet temps at various psi.

The R33 turbo on my RB20 does make a fair bit more on the dyno at 1Bar (14.7psi) as opposed to 0.8bar (12psi), but it was on different dyno's, but using the same shootout mode. Inlet temps did not skyrocket either. R33 turbo's seem to be still good at 15ish- psi..... whereas R34's seem to go off at 12.

Fixxxer

Also shaft speed can be the killer. So just being on full song for a long long period can make it fail. Have seen a HKS 2530 fail with steel wheel so its possible to kill others also.

Fixxxer....

What power is the R33 turbs making on your Rb20?

Made 229HP@wheels at 0.82bar, held that all the way to redline I'm sure, with a ProfecA.

Think it made 247HP at 1bar, that was with the original owner, not the guy I bought it off. Might have been a few years ago but the graphs in the car.

Fixxxer

okay.

So thats 170rwkw at 0.8 bar

and 184rwkw at 1.0 bar.

the R34 Turbo on my car (which is an R34) made 200rwkw on 12 psi (0.8 bar) which is about 270rwHP

The R34 turbos are reasonably good for about 20 rwkw more on average than the R33 turbos due to their ability to flow much more through their exhaust housing.

BASS OUT

On an RB25 I wouldn't go over 12psi for the street. I blew mine at 13psi.

On an RB20 1 bar seems safe.

Just thought it would be funny to quote myself.

You can run more boost with any of these turbos if you have them fitted to an RB20.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...