Jump to content
SAU Community

Recommended Posts

running rb30det with orc triple plate and shitty rb20det box

looking at 33 gtst boxes. they no worries

but r34 gtt - does it work with push or pull type clutch

i aint very bright mechanically (or in many other aspects for that matter)

need to know if i can bolt up r34gtt box to my orc triple plate setup

not a teeny bopper dreamer, just need some advice.

cheers, mark

Link to comment
https://www.sau.com.au/forums/topic/113375-r34gtt-gearbox/
Share on other sites

R34 box is pull, and you can get a thing to convert your push clutch to pull, but im not sure how well it works, but i know there are kits for this, orc mostlikely make one, as my twinplate clutch says it can be used on GTR and GTSTs but its a pull type, and yu can get a optional thing to make it push.

hope that kinda helps.

How is it driving with the tripple plate, is there even a smaller amount of play to find a friction point? espically in the 31 with it al the top of the pedal, how do you find it?

Link to comment
https://www.sau.com.au/forums/topic/113375-r34gtt-gearbox/#findComment-2093439
Share on other sites

R34 box is pull, and you can get a thing to convert your push clutch to pull, but im not sure how well it works, but i know there are kits for this, orc mostlikely make one, as my twinplate clutch says it can be used on GTR and GTSTs but its a pull type, and yu can get a optional thing to make it push.

hope that kinda helps.

How is it driving with the tripple plate, is there even a smaller amount of play to find a friction point? espically in the 31 with it al the top of the pedal, how do you find it?

The 34 uses a pull clutch , the box is not any different, just the fork, pivot and the way the slave mounts on the bellhousing are different.

Link to comment
https://www.sau.com.au/forums/topic/113375-r34gtt-gearbox/#findComment-2093485
Share on other sites

R34 box is pull, and you can get a thing to convert your push clutch to pull, but im not sure how well it works, but i know there are kits for this, orc mostlikely make one, as my twinplate clutch says it can be used on GTR and GTSTs but its a pull type, and yu can get a optional thing to make it push.

hope that kinda helps.

How is it driving with the tripple plate, is there even a smaller amount of play to find a friction point? espically in the 31 with it al the top of the pedal, how do you find it?

thanks for the answer fellas

looks like ill go with the usual and get a bloody r33 box. $$ but oh well. rb20det boxes serve me well but sick of breaking them.

as for triple plate, no play. bout 1/2 centimetre at top of clutch pedal. i find it ok because is obnly driven at track mostly so wheel spin is no drama. but taking off from traffic on a hill is terriblly hard without spinning wheels.

r33 box it is!!

Link to comment
https://www.sau.com.au/forums/topic/113375-r34gtt-gearbox/#findComment-2093924
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...